Section 2 - OPERATING INSTRUCTIONS

WARNING

DO NOT attempt to operate the machine until you have read this manual thoroughly and become familiar with all controls and operating procedures. Serious injury or damage can result.

2.1PRE-START CHECK LIST

Make the following checks and perform the service required before each start-up.

2.1.1.Check tires and add or release air as needed to bring pressure to 12 P.S.I. front and rear.

2.1.2.Check guards, deflectors and covers to make sure all are in place and securely tightened.

2.1.3.Check engine oil and add as needed to bring level up to the FULL mark. Refer to engine owner’s manual for oil specifications. See Figure 2.1.

ENGINE OIL DIPSTICK

SAFE LEVEL

AREA

FIGURE 2.1

2.1.4.Check all controls to make sure they operate freely and correctly. (Refer to section “FAMILIARIZATION”.)

2.1.5.Clean exterior surfaces of cutting deck and engine of any accumulation of dirt, grass, oil, etc. Keep engine air intake screen and cooling fins clear at all times.

2.1.6.Add fuel to tank with machine out of doors where fumes can safely dissipate. Refer to engine owner’s manual for fuel specifications. Make sure fuel filler cap is tight after filling tank. Open vent screw on fuel cap by turning counterclockwise. Also open fuel valve, located in fuel line. See Figure 2.2.

VENT SCREW

FUEL FILLER CAP

WITH VENT SCREW.

TIGHTEN CAP AND

OPEN VENT SCREW

AFTER REFUELING.

FUEL CAP

FUEL VALVE

FIGURE 2.2

2.2ENGINE OPERATION 2.2.1. STARTING ENGINE

1.Make sure both motion control levers are lifted fully up and out into their neutral lock positions. See Figure 1.5.

2.Make sure blade switch is pushed in to its off (‘0’) position. See Figure 1.7.

3.Make sure parking brake is engaged. See Figure 1.6.

IMPORTANT: Engine will not crank or start unless steps 1 thru 3 have been taken.

4.Make sure vent screw on fuel cap and fuel valve in fuel line are both open. See Figure 2.2. IMPORTANT: Failure to open vent screw and/or fuel valve will prevent engine from starting, or will cause engine to stall after starting.

5.Sit squarely in operator seat.

6.Apply choke. See Figure 1.3.

7.Turn key to “START” position and hold until engine starts. See Figure 1.2. NOTE: If engine does not start after 5 seconds, release key, wait 20 seconds, then attempt starting again. (If engine still fails to start, refer to the troubleshooting section of both mower and engine manuals.)

8.After engine starts, turn off choke and adjust engine to desired speed position. Allow a brief warm- up until engine runs smooth.

WARNING

DO NOT leave machine with engine running. STOP engine. STOP blades. Engage park brake. Remove key. DO NOT park machine on slopes.

2.2.2. STOPPING ENGINE

1.Stop engine by turning key to “STOP” position. See Figure 1.2.

8

Page 7 Page 9
Page 8
Image 8
Snapper SZT18426BVE, SZT20486BVE PRE-START Check List, Engine Operation 2.2.1. Starting Engine, Stopping Engine
Page 7 Page 9

SZT18426BVE, SZT20486BVE specifications

The Snapper SZT18426BVE and SZT20486BVE are advanced lawn care machines designed for homeowners and professionals who demand high performance and reliability in their lawn maintenance tasks. Both models exhibit a combination of power, versatility, and user-friendly features that make them stand out in the market.

The Snapper SZT18426BVE is equipped with an 18 horsepower engine, making it a robust performer for various lawn sizes and types. Its cutting deck is 26 inches wide, which allows for efficient mowing even in tighter spaces. The SZT20486BVE takes it up a notch with a more powerful 20 horsepower engine and a wider 48-inch cutting deck, enabling it to cover more ground quickly, making it ideal for larger properties.

One notable feature of both models is the Zero-Turn technology, which allows for unmatched maneuverability. This function enables the operator to turn on a dime, facilitating access to corners and obstacles with ease. This is particularly beneficial for mowing around trees, flower beds, and other landscaping features. The comfort of the operator is also a priority; both models come with fully adjustable high-back seats that provide ample support during extended use.

Equipped with advanced cutting technologies, these Snapper models feature a patented mowing system that ensures a precise cut while maintaining the health of the grass. The adjustable cutting height offers versatility to achieve the desired grass length, accommodating various lawn conditions and preferences.

Moreover, both the SZT18426BVE and SZT20486BVE are designed with durability in mind. Their rugged frames and heavy-duty components ensure long-lasting performance, making them investments that stand the test of time. Additionally, maintenance is straightforward with easily accessible parts and a simple design that allows users to keep their machines in peak condition with minimal effort.

Safety features, such as the operator presence control, ensure that the mower will stop when the operator is not in a seated position, providing peace of mind during use. Both models also come with an easy-to-use dashboard that allows for quick adjustments on the go, including speed control and blade engagement.

Overall, the Snapper SZT18426BVE and SZT20486BVE are excellent choices for those seeking efficient, reliable, and user-friendly zero-turn lawn mowers that combine power and innovative features for a superior mowing experience.
Top Page Image Contents