Sony 4-216-840-0 Xras, Xwe, Asyo, Asyi, Avdd, Bias, Rfi, Avss, Fili, Filo, Cltv, Xlrf, Lddr, Trdr

Pin No.	Pin Name		I/O	Description
45		A09	O	Address signal output to the D-RAM (IC124)
46		XRAS	O	Row address strobe signal output to the D-RAM (IC124)		“L” active
47		XWE	O	Write enable signal output to the D-RAM (IC124)	“L” active
48		D1	I/O
49		D0	I/O	Two-way data bus with the D-RAM (IC124)
50		D2	I/O
51		D3	I/O
52		MVCI	I (S)	Digital in PLL oscillation input from the external VCO		Not used (fixed at “L”)
53		ASYO	O	Playback EFM full-swing output terminal
54		ASYI	I (A)	Playback EFM asymmetry comparator voltage input terminal
55		AVDD	—	Power supply terminal (+3.3V) (analog system)
56		BIAS	I (A)	Playback EFM asymmetry circuit constant current input terminal
57		RFI	I (A)	Playback EFM RF signal input from the CXA2523AR (IC101)
58		AVSS	—	Ground terminal (analog system)
59		PCO	O (3)	Phase comparison output for master clock of the recording/playback EFM master PLL
60		FILI	I (A)	Filter input for master clock of the recording/playback master PLL
61		FILO	O (A)	Filter output for master clock of the recording/playback master PLL
62		CLTV	I (A)	Internal VCO control voltage input of the recording/playback master PLL
63		PEAK	I (A)	Light amount signal (RF/ABCD) peak hold input from the CXA2523AR (IC101)
64		BOTM	I (A)	Light amount signal (RF/ABCD) bottom hold input from the CXA2523AR (IC101)
65		ABCD	I (A)	Light amount signal (ABCD) input from the CXA2523AR (IC101)
66		FE	I (A)	Focus error signal input from the CXA2523AR (IC101)
67		AUX1	I (A)	Auxiliary signal (I3 signal/temperature signal) input from the CXA2523AR (IC101)
68		VC	I (A)	Middle point voltage (+1.65V) input from the CXA2523AR (IC101)
69		ADIO	O (A)	Monitor output of the A/D converter input signal	Not used (open)
70		AVDD	—	Power supply terminal (+3.3V) (analog system)
71		ADRT	I (A)	A/D converter operational range upper limit voltage input terminal (fixed at “H” in this set)
72		ADRB	I (A)	A/D converter operational range lower limit voltage input terminal (fixed at “L” in this set)
73		AVSS	—	Ground terminal (analog system)
74		SE	I (A)	Sled error signal input from the CXA2523AR (IC101)
75		TE	I (A)	Tracking error signal input from the CXA2523AR (IC101)
76		DCHG	I (A)	Connected to the +3.3V power supply
77		APC	I (A)	Error signal input for the laser automatic power control		Not used (fixed at “H”)
78		ADFG	I (S)	ADIP duplex FM signal (22.05 kHz ± 1 kHz) input from the CXA2523AR (IC101)
79		F0CNT	O	Filter f0 control signal output to the CXA2523AR (IC101)
80		XLRF	O	Serial data latch pulse signal output to the CXA2523AR (IC101)
81		CKRF	O	Serial data transfer clock signal output to the CXA2523AR (IC101)
82		DTRF	O	Writing serial data output to the CXA2523AR (IC101)
83		APCREF	O	Control signal output to the reference voltage generator circuit for the laser automatic power
				control
84		LDDR	O	PWM signal output for the laser automatic power control		Not used (open)
85		TRDR	O	Tracking servo drive PWM signal (–) output to the BH6511FS (IC152)
86		TFDR	O	Tracking servo drive PWM signal (+) output to the BH6511FS (IC152)
87		DVDD	—	Power supply terminal (+3.3V) (digital system)
88		FFDR	O	Focus servo drive PWM signal (+) output to the BH6511FS (IC152)
89		FRDR	O	Focus servo drive PWM signal (–) output to the BH6511FS (IC152)

* I (S) stands for schmitt input, I (A) for analog input, O (3) for 3-state output, and O (A) for analog output in the column I/O.

– 32 –