139
Menu List
Appendix
To specify snapshot data at the time of startup (menu page 944)
You can store the data set in the menus from menu pages in the 400s* (MEM menu) to 800s (PIP menu)
with 0 to 99 snapshot numbers.
When you enter the number 0 to 99 under STARTUP in menu page 944, the switcher starts with the
selected snapshot data when the power is turned on.
When you select Setup under STARTUP, the switcher starts with the currently selected values in the
SETUP menu.
* The date and time setting on menu page 440 ar e not registered in the snapshot number.
To recall the snapshot number using the DIRECT RECALL button (menu page 945)
Select any of Bank 0 to Bank 9 under DRCT RCT on menu page 945.
The numbers 0 to 9 for Bank correspond to the tens digit o f the snapshot number. Specifying Bank 0
allows you to recall snapshot numbers 0 to 9, Bank 1 to recall snapshot numbers 10 to 19 etc. and Bank
9 to recall snapshot numbers 90 to 99.
For example, specifying Bank 3 allows you to recall snapshot numbers 30 to 39 by pressing and lighting
up the DIRECT RECALL button then pressing numeric buttons 0 to 9.
900 OUTPUT.. 930 SAFETTL.. 936 DISPLAY Off, On Allows display of a frame in a safe area (80%
or 90% of the display) of the signal selected
under BUS SEL when DISPLAY is set to On.
Setting CROSS to On allows display of a
cross indication with a frame.
Setting SIDE CUT to On allows display of the
side cuts (vertical lines indicating the position)
with a frame.
BUS SEL PGM, PVW, AUX1, AUX2, MV
CROSS Off, On
SIDE
CUT
Off, On
PANEL.. 940 DSKBUS.. 941 XPT BTN 1 to 12 Sets DSK SOURCE signal to be assigned
automatically to the DSK FILL signal selected
with the DSK/AUX select button 1 to 12.
FILL (4-character indication)
SIGNAL IN 1, IN 2, IN 3, IN 4, IN 5, IN
6, IN 7, IN 8, IN 9, FM 1, FM 2,
MAT1, MAT2, CLBR
SOURCE (4-character indication)
SW / CAM.. 942 MOD
ENBL
Both, SW Only, CAM Only Allows you to set whether the switcher is to
function in either CAM or SW mode only.
When either is selected, the switcher does not
function in the other mode.
To enable the setting, press the F4 (MOD
CHG) control.
MOD
CHG
Exec
TRANS.. 943ME
AUTO
0 to 999 (30) Sets the transition time of each effect.
Setting BUS TGL to On enables use of the
PGM and NEXT cross-point buttons in BUS
TGL mode.
For details, see “Setting the Bus Mode for the
Cross-Point Buttons (Menu Page 943)” on
page 56.
DSK
AUTO
0 to 999 (30)
PIP
AUTO
0 to 999 (30)
BUS TGL Off, On
MODE.. 944 BEEP Off, On Sets for the beep to sound or not, under
BEEP.
Selects the snapshot data recalled at the time
of startup under STARTUP.
For details, see “To specify snapshot data at
the time of startup (menu page 944)” on page
139.
STARTUP
Setup, 0 to 99
BANK.. 945DRCT
RCL
Bank 0, Bank 1, Bank 2, Bank
3, Bank 4, Bank 5, Bank 6,
Bank 7, Bank 8, Bank 9
Sets the tens digit of the snapshot number
when recalling it using the DIRECT RECALL
button.
For details, see “To recall the snapshot
number using the DIRECT RECALL button
(menu page 945)” on page 139.
Setting menu Setting item Description