Overview 1 Chapter

bTrigger mode

PARA: Operates both internal and external VTRs.

INT: Operates the internal VTR only.

EXT: Operates the external VTR only.

cExtender

“EX” is displayed when a lens extender is used.

dColor temperature

Indicates the currently selected color temperature.

eDC IN / battery voltage / remaining capacity Indicates the battery voltage or the remaining capacity of an attached internal battery pack, an AC adaptor, or an external battery (a battery connected to the DC IN connector).

When the power is supplied from an external battery, “DC IN” appears here.

When the DISP BATT REMAIN item is set to INT on the VF DISP 2 page of the OPERATION menu, the battery voltage is not indicated.

However, when the Anton Bauer intelligent battery system or the BP-GL65/GL95 battery pack is used, the remaining battery capacity is automatically detected and indicated in steps of 10%.

• Until the remaining battery capacity is reduced to 40%, the indications MAX, 90%, 80%...40% are displayed for three seconds in the viewfinder each time the remaining battery capacity reduces by 10%.

• When the remaining battery capacity is less than 40%,

the indication is displayed all the time.

• When the remaining battery capacity is less than 10%*, the indication flashes. When the remaining battery capacity is reduced further, the “LOW” flashes.

*This value can be set to either 10% or 20% on the FUNCTION 2 page of the OPERATION menu.

f* (Asterisk indicator)

Flashes when the color bars are displayed and is recorded together with the color bars.

g16:9 mode recording indicator (DSR-450WS/

450WSP only)

Indicates recording in the 16:9 mode. This indicator is recorded together with the color bars.

hSetting change and adjustment progress message

display area

For details, see “Display modes and setting change confirmation/adjustment progress messages” on page 99.

iEXT/IV indicator (DSR-450WS/450WSP only) Displayed when a CBK-SC01 Composite Input Board is installed for input of external composite signals.

jRecording format

Indicates the current recording format.

kIris setting/auto iris override

Indicates the F value (iris setting) of the lens.

Also, the auto iris override is displayed using two squares which appear in the upper and lower parts respectively.

For details, see “Adjusting the iris” on page 55.

lRemaining tape capacity

Indicates the remaining tape recording time (in minutes) of the VTR.

Examples of remaining tape recording time indication

Indication

Remaining tape recording time

F - 30

Full to 30 minutes

 

 

 

30

- 25

30 to 25 minutes

 

 

 

25

- 20

25 to 20 minutes

 

 

 

20

- 15

20 to 15 minutes

 

 

 

15

- 10

15 to 10 minutes

 

 

 

10

- 5

10 to 5 minutes

 

 

5 - 0

5 to 0 minutes

 

 

No display

0 minute

 

 

 

mAudio level

Indicates the level of audio channel 1 and channel 2. The peak indication of the VTR level meter is related as follows to the audio level when an 1kHz sine wave is input.

Audio channel 1 level indicator

Audio channel 2 level indicator

VTR level meter indicator

nOperation/error message display area

For details, see “Operation/error messages” on page 127.

oShutter speed

Indicates the shutter speed or the shutter mode. However, if the SHUTTER switch (page 10) is set to OFF, nothing is displayed.

1/100, 1/125, 1/250, 1/500, 1/1000, 1/2000: Shutter speed (in seconds) in standard mode (scan mode: I)

1/40, 1/60, 1/120, 1/125, 1/250, 1/500, 1/1000, 1/2000:

Shutter speed (in seconds) in standard mode (scan mode: PsF)

ECS: In ECS (Extended Clear Scan) mode

EVS: In EVS (Super Enhanced Vertical Definition System) mode

1F to 8F, 16F (DSR-450WS/450WSP only): Number of frames in the slow speed shutter mode

pGain

Indicates the gain of the video amplifier, as set by the GAIN switch.

22 Location and Function of Parts