Specifications
|
|
Picture tube | 0.25 mm aperture grille pitch |
| 17 inches measured diagonally |
|
Viewable image size Approx. 327 × 241 mm (w/h)
| (12 7/8 × 9 1/2 inches) |
| 15.9” viewing image |
Resolution | Horizontal: Max. 1280 dots |
| Vertical: Max. 1024 lines |
Standard image area | Approx. 300 × 225 mm (w/h) |
| |
| (11 7/8 × 8 7/8 inches) |
| or |
| Aprrox. 293 × 234 mm (w/h) |
| (11 5/8 × 9 1/4 inches) |
Deflection frequency |
|
| Horizontal: 30 to 85 kHz |
| Vertical: 48 to 150 Hz |
AC input voltage/current | |
| 100 to 120 V, 50/60 Hz, 1.7 A |
| 220 to 240 V, 50 – 60 Hz, 1.2 A |
Power comsumption |
|
| Max. 140 W |
Dimensions | 403.6 × 426.3 × 450 mm (w/h/d) |
| (16 × 16 7/8 × 17 3/4 inches) |
Mass | Approx. 20 kg (44 lb) |
|
|
Picture tube | 0.25 mm aperture grille pitch |
| 20 inches measured diagonally |
| |
Viewable image size Approx. 387 × 292 mm (w/h) | |
| (15 1/4 × 11 1/2 inches) |
| 19.0” viewing image |
Resolution | Horizontal: Max. 1600 dots |
| Vertical: Max. 1200 lines |
Standard image area | Approx. 373 × 280 mm (w/h) |
| |
| (14 3/4 × 11 1/8 inches) |
| or |
| Aprrox. 350 × 280 mm (w/h) |
| (13 7/8 × 11 1/8 inches) |
Deflection frequency |
|
| Horizontal: 30 to 96 kHz |
| Vertical: 48 to 160 Hz |
AC input voltage/current | |
| 100 to 120 V, 50/60 Hz, 1.7 A |
| 220 to 240 V, 50 – 60 Hz, 1.2 A |
Power comsumption |
|
| Max. 150 W |
Dimensions | 472 × 493.5 × 501 mm (w/h/d) |
| (18 5/8 × 19 1/2 × 19 3/4 inches) |
Mass | Approx. 30 kg (66 lb 2 oz) |
Design and specifications are subject to change without notice.
Troubleshooting
This section may help you isolate a problem and as a result, eliminate the need to contact technical support, allowing continued productivity.
No picture
/If neither the u (power) indicator nor the POWER SAVING indicator is not lit.
—Check that the power cord is properly connected.
—Check that the power switch is in the “on” position.
/If the POWER SAVING indicator is lit.
—Check that your computer power switch is in the “on” position.
—The monitor will recover when you press any key on the keyboard of the computer.
—Check that the video cable is properly connected and all plugs are firmly seated in their socket.
—Check that the 5 BNC's are connected in the right order (from power cord side: Red-
—Ensure that no pins are bent or pushed in the HD15 connector of the cable.
—Check that the video card is seated completely in a proper bus slot.
—Check that the video frequency range is
within that specified for the monitor. | EN |
— If using a Macintosh system, check that the |
|
| |
Macintosh adapter and the video signal |
|
cable are properly connected. |
|
/ If the u (power) and/or the POWER SAVING |
|
indicators are both flashing. |
|
— Turn the monitor off and on. If the indicator |
|
is off, the monitor is in the normal |
|
condition. If the indicator is still flashing, |
|
there is a potential monitor failure. |
|
/ If you do the above procedures and the |
|
monitor does not recover. |
|
— Unplug the video cable (HD15/5 BNC's) |
|
then press and hold the > + button for 2 |
|
seconds to display the color bars. Then, |
|
turn the monitor off and on by pressing the |
|
u power switch. |
|
If the monitor does not recover, the monitor |
|
is out of order. |
|
/ If your computer is a Macintosh system and |
|
the Macintosh adapter has micro switches |
|
— Check that the micro switches are properly |
|
set for your system. (See the adapter |
|
manual.) |
|
Picture is scrambled
/Check your graphics board manual for the proper monitor setting on your Multiscan 17seII/20seII.
/Check this manual and confirm that the graphic mode and the frequency at which you are trying to operate is supported. Even within the proper range some video boards may have a sync pulse that is too narrow for the monitor to sync correctly.
13
