THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.

(In addition to this, the necessary note is printed in each block.)

For schematic diagrams.

Note:

All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums.

All resistors are in Ω and 1/4 W or less unless otherwise specified.

¢ : internal component.

2 : nonflammable resistor.

1 : fusible resistor.

C : panel designation.

Note: The components identified by mark !or dotted line with mark !are critical for safety.

Replace only with part number specified.

S : B+ Line.

T : B– Line.

H : adjustment for repair.

Voltages and waveforms are dc with respect to ground in service mode.

Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal produc- tion tolerances.

Waveforms are taken with a oscilloscope.

Voltage variations may be noted due to normal produc- tion tolerances.

Circled numbers refer to waveforms.

Signal path.

F : FM

E : PB (MD)

m : PB (TAPE)

n : REC

J : CD

c : digital out

Abbreviation

SP

: Singapore model.

HK

: Hong Kong model.

For printed wiring boards.

Note:

X : parts extracted from the component side

p : parts mounted on the conductor side.

® : Through hole.

¢ : internal component.

b: Pattern from the side which enables seeing. (The other layers' patterns are not indicated.)

Caution:

 

 

 

 

 

 

Pattern face side: Parts on the pattern face side seen from the

(Side B)

 

pattern face are indicated.

Parts face side: Parts on the parts face side seen from the

(Side A)

 

parts face are indicated.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Indication of transistor

 

 

 

 

 

 

 

C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Q

 

 

These are omitted

BC E

 

 

 

 

 

 

 

 

 

 

 

 

 

 

B E

 

 

 

 

 

These are omitted

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

WAVEFORMS

– BD SECTION –

1

1.3 ± 0.3 Vp-p

IC101 (RFO) (PLAY Mode)

500 mV/DIV, 500 ns/DIV

2

Approx.

100 mVp-p

IC101 (TEI) (PLAY Mode)

50 mV/DIV, 1 s/DIV

3

Approx.

150 mVp-p

IC101 2 (FEI) (PLAY Mode)

50 mV/DIV, 1 s/DIV

4

2.6 Vp-p

7.6 s

IC103 3 (MDP) (PLAY Mode)

5

5.1 Vp-p

136 s

IC103 @• (RFCK)

6

5.3 Vp-p

14 ns

IC103 @∞ (XPCK)

7

5 Vp-p

474 ns

IC103 @™ (BCLK)

8

5.1 Vp-p

22.8 s

IC103 (LRCK)

9

4.6 Vp-p

16.9344 MHz

IC104 6 (XTO)

HCD-SD1

– MAIN SECTION –

1

4.3Vp-p

5 MHz

IC701 (XI)

2

2.6 Vp-p

32 kHz

IC701 (XI)

– 21 –

– 22 –

Page 19
Image 19
Sony hcd-sd1 Waveforms BD Section, For schematic diagrams, For printed wiring boards, Indication of transistor