2 Place the supplied flange focal length adjustment chart approximately 3 meters from the camera and adjust the lighting to get an appropriate video output level.
About 3 meters (10 ft)
3 Loosen the Ff (flange focal length) ring lock screw.4 With either manual or power zoom, set the zoom ring to telephoto.5 Aim at the flange focal length adjustment chart and turn the focus ring to focus the image.
6 Set the zoom ring to wide angle.7 Turn the Ff ring to bring the chart into focus.Take care not to move the distance ring.
8 Repeat steps 4 through 7 until the image is in focus at both telephoto and wide angle.
9 Tighten the Ff ring lock screw.Setting the Focus Assist Function
Using the OPERATION menu, the assist functions for easier focusing on the viewfinder screen can be activated.
Adding a VF detail signal
Adding a VF detail signal to sharp edges in the image on the viewfinder screen makes it easier to check the focusing condition by observing changes in the detail signal or in the color converted from the detail signal (color detail).
The focus setting where the detail signal becomes strongest is the best focus setting.
1 Turn on the camera.
2 Set the the DISPLAY/MENU switch to MENU while holding the menu control knob pressed.
The camera enters Menu mode, and “TOP” is displayed at the upper right corner of the screen.
3 Rotate the menu control knob to align the pointer to “TOP” and push on the knob.
The TOP MENU screen is displayed.
<TOP MENU>
USER
USER MENU CUSTOMIZE
ALL
OPERATION
PAINT
MAINTENANCE
FILE
DIAGNOSIS
4 Rotate the menu control knob to align the pointer to OPERATION and push on the knob.
The CONTENTS page of the OPERATION menu is displayed.
CONTENTS | 00 TOP |
01.<VF DISPLAY> 02.<'!'IND> 03.<VF MARKER> 04.<VF DETAIL> 05.<FOCUS ASSIST> 06.<ZEBRA> 07.<CURSOR> 08.<VF OUT> 09.<SWITCH ASSIGN1> 10.<SWITCH ASSIGN2>
5 Rotate the menu control knob to align the pointer to <VF DETAIL> and push on the knob.
The <VF DETAIL> page is displayed.
<VF | DETAIL> |
| 04 TOP | ||
VF | DETAIL | : | ON | 25% | |
CRISP | : | 0 |
| ||
FREQUENCY: | 9M |
| |||
FAT | MODE | : | OFF | ||
FLICKER | : | OFF | |||
AREA |
| : | 70% | ||
ZOOM | LINK: | 100% | |||
COLOR | DETAIL | : | ON BLUE | ||
PEAK | COLOR | : | ON | ||
CHROMA LEVEL: | 100% | ||||
|
|
|
|
|
|
6 Rotate the menu control knob to align the pointer to the item to be set and push on the knob.
To use the VF detail signalSet VF DETAIL to ON to activate the VF detail function to add the detail signal to sharp edges in the image. You can adjust the signal level (strength) in the range of 0 to 100% (default 25%).
You can adjust the characteristics of the detail signal with the menu items below:
CRISP: Adjust to eliminate fine portions of the detail signal.
FREQUENCY: Change the detection band of sharp edges.
FAT MODE: Turn the function ON/OFF to thicken the detail signal.
FLICKER: Turn the function ON/OFF to flicker the detail signal, which makes it easier to check the signal on a CRT screen.
AREA: To limit the area where to display the detail signal.
ZOOM LINK: Set the VF detail level at the full WIDE position. (The VF detail level changes according to the zoom position.)
To use the color detailSet COLOR DETAIL to ON to convert the VF detail signal to a specified color. This makes it easier to check the signal on an LCD screen, including the viewfinder screen. The display color can be selected at the column next to ON.
You can adjust the coloring with the menu items below: PEAK COLOR: Turn the function ON/OFF to change the
color where the detail signal is strongest.
CHROMA LEVEL: To reduce the chroma components of the video signal (only for video signals on the viewfinder).
7 Rotate the menu control knob to display the desired setting and push on the knob.
16 | Preparatory Settings |
|
|