continued...
Learning functions from other Remote Controls
To eliminate the amount of remote controls you need, this remote control has a learning feature. Once set up as explained below, it can be used in place of your other remote controls.
It is recommended that you make a note of what each button has been taught (you can use the table provided with the remote control).
Before you start and for accurate learning, please read below instructions:
• Choose the button (a-g) you want to learn. The buttons which can learn a new function, have a blue dot. See fig. 3 to find out the possible buttons.
• Do not move the remote units during the learning procedure.
• Be sure to keep holding down the learning button until your commander reacts as described.
• Use fresh batteries in both remote units.
• Avoid learning in places subjects to direct sunlight or a strong fluorescent light.
• Noise may interfere during the learning procedure.
• The remote control detector area may differ depending on each remote unit. If learning does not work, try changing the positions of the two remote controls.
• It is possible that some specific remote control signals may not be learned.
• If you do not perform the learning steps within 20 seconds at any point during the process, the learning mode
ends.
fig. 1
2-3 cm.

1Position both remote controls as shown (see fig. 1).

fig. 3

2 Press and hold the t button of this TV remote control for

a

approximately 6 seconds, until the AUX green light starts flashing

 

(see fig.2).

3Press the button (a-g, see fig. 3) of this TV remote control on which you wish to store a learned function.

 

 

 

 

 

 

 

 

Once the selected button has been pressed, the VCR, TV, DVD and

b

 

 

 

 

 

 

AUX illuminate flash in order (see fig. 4).

c

 

 

 

 

 

 

g

4 Press the button from the other remote control that you wish to teach your

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TV remote control.

 

 

 

 

 

 

 

•During the data transfer process, all the four lights illuminate at the same time (see fig. 5).

d

 

• As soon as data transfer is finished, the AUX green light starts

 

 

 

 

 

flashing (see fig. 6).

e

This TV remote

 

 

Other remote

control

 

 

 

 

control

 

 

fig. 2

 

 

V

D

 

 

 

 

V

 

 

R

T

 

D

 

 

 

 

U

C

 

 

 

 

A

 

 

 

 

X

V

 

 

 

 

 

 

 

MODE

 

 

 

 

 

 

6 sec.

 

 

fig. 4

 

 

V

D

 

 

 

 

V

 

 

T

 

 

D

 

 

R

 

 

U

 

C

 

 

 

A

 

 

 

 

X

V

 

 

 

 

MODE

5If you wish to record other functions repeat steps 2-4 (read before the warning below), otherwise go to step 6.

f

• In case you try to select one button which has been already

learned, all the four lights will momentarily flash very shortly and

 

 

the remote control automatically return to the same condition as

 

in the step 2 with the AUX light flashing

•In case you try to select a not-learnable button, the remote control stay in to the same condition as in the step 2 with the AUX light flashing.

6Press the t button to finish the learning process.

7Check that all the learning functions have been learned correctly.

fig. 5

 

V

D

 

 

V

 

T

 

D

 

R

 

U

C

 

 

A

 

 

X

V

 

 

 

MODE

fig. 6

 

V

D

 

 

V

 

T

 

D

 

R

 

U

C

 

 

A

 

 

X

V

 

 

 

MODE

•To use a learned function later, press the T or t buttons to select AUX and next press the relevant button.

•Always remember to press the T or t button until the green light iluminates according to the equipment you want to operate with this remote control: VCR, TV,

DVD or AUX.

24 Additional Information