• IC501 System Control (M30620MC-406FP) (MAIN board)
Pin No. | Pin Name | I/O | Function |
|
|
|
|
1, 2 | NC | O | Not used (Fixed at “L”) |
|
|
|
|
3 | C1ER | O | C1 error rate voltage output (Fixed at “L”) (Not used) |
4 | ADER | O | AD error rate voltage output (Fixed at “L”) (Not used) |
|
|
|
|
5 | SQSY | I | ADIP sync or subcode Q sync input from CXD2654R |
|
|
|
|
6 | RMC | I | Remote controls |
|
|
|
|
7 | A1 IN | I | A1 Control input (Fixed at “L”) |
|
|
|
|
8 | BYTE | I | Data bus changed input (Fixed at “L”) |
|
|
|
|
9 | CNVSS | — | Ground |
|
|
|
|
10 | O | Not used (Fixed at “L”) | |
|
|
|
|
11 | O | Not used (Fixed at “L”) | |
|
|
|
|
12 | S.RST | I | System rest input |
|
|
|
|
13 | XOUT | O | Main clock output (7.0MHz) |
14 | GND | — | Ground |
|
|
|
|
15 | XIN | I | Main clock input (7.0MHz) |
16 | +3.3V | — | +3.3V power supply |
17 | NMI | I | (Fixed at “H”) |
|
|
|
|
18 | DQSY | I | Digital in sync input |
|
|
|
|
19 | P.DOWN | I | Power down detection input “L”: Power down |
|
|
|
|
20 | KEYBOARD CLK | O | Not used |
|
|
|
|
21 | KEYBOARD DATA | O | Not used |
|
|
|
|
22 | BEEP OUT | — | Not used |
|
|
|
|
23 | XINIT | I | Interrupt status input from CXD2654R |
|
|
|
|
24 to 27 | NC | O | Not used |
|
|
|
|
28 | L3 CLOCK | O | Serial clock signal output to IC301 |
|
|
|
|
29 | NC | O | Not used |
30 | LC DATA | O | Serial data signal input to IC301 |
|
|
|
|
31 | SWDT | O | Writing data signal output to the serial bus |
32 | SRDT | I | Reading data signal input from the serial bus |
33 | SCLK | O | Clock signal output to the serial bus |
34 | FLCS | O | Chip select signal output to the display driver |
35 | FLDATA | O | Serial data signal output to the display driver |
36 | NC | O | Not used (Fixed at “L”) |
37 | FLCLK | O | Serial clock signal output to the display driver |
38 to 41 | NC | O | Not used |
|
|
|
|
42, 43 | JOG1, JOG0 | I | Not used |
44 | NC | O | Not used |
|
|
|
|
45 | A1 OUT | O | A1 output |
46 | NC | O | Not used |
47 | L3 MODE | O | Serial mode signal output to IC301 |
|
|
|
|
48 | DA.RST | O | Not used Reset: “L” |
49 | MUTE | O | DA line out muting output Mute: “L” |
|
|
|
|
50 | STB | O | Strobe signal output to the power supply circuit Power supply ON: “H”, stand by: “L” |
|
|
|
|
51 | CHACK IN | I | Detection input from the |
|
|
|
|
52 | NC | I | Not used (Fixed at “L”) |
|
|
|
|
53 | I | Detection input from the loading out switch. Loaded out position: “L”, Others: “H” | |
|
|
|
|
54 | LDIN | I | Loading motor control input |
|
|
|
|
55 | LDOUT | O | Loading motor control output |
|
|
|
|
56 | O | Loading motor voltage control output Low voltage: “H” | |
|
|
|
|
57, 58 | NC | O | Not used (Fixed at “L”) |
|
|
|
|
59 | I | Detection signal input from the recording position detection switch | |
|
|
|
|
51