MDX-CA680/CA680X
•SERVO BOARD IC302 CXA2523AR (RF AMP, FOCUS/TRACKING ERROR AMP)
Pin No. | Pin Name | I/O |
|
| Description |
|
|
|
| ||
1 | I | I | |||
|
|
|
| ||
2 | J | I | |||
|
|
|
| ||
3 | VC | O | Middle point voltage (+1.65V) generation output terminal | ||
|
|
|
| ||
4 to 9 | A to F | I | Signal input from the optical | ||
|
|
|
| ||
10 | PD | I | Light amount monitor input from the optical | ||
|
|
|
| ||
11 | APC | O | Laser amplifier output terminal to the automatic power control circuit | ||
|
|
|
| ||
12 | APCREF | I | Reference voltage input terminal for setting laser power | ||
|
|
|
|
|
|
13 | GND | — | Ground terminal |
|
|
|
|
|
|
| |
14 | TEMPI | I | Connected to the temperature sensor | Not used (open) | |
|
|
|
| ||
15 | TEMPR | O | Output terminal for a temperature sensor reference voltage Not used (open) | ||
|
|
|
| ||
16 | SWDT | I | Writing serial data input from the MD mechanism controller (IC501) | ||
|
|
|
| ||
17 | SCLK | I | Serial data transfer clock signal input from the MD mechanism controller (IC501) | ||
|
|
|
| ||
18 | XLAT | I | Serial data latch pulse signal input from the MD mechanism controller (IC501) | ||
|
|
|
| ||
19 | XSTBY | I | Standby signal input terminal “L”: standby (fixed at “H” in this set) | ||
|
|
|
| ||
20 | F0CNT | I | Center frequency control voltage input terminal of internal circuit (BPF22, BPF3T, EQ) input | ||
terminal |
|
| |||
|
|
|
|
| |
|
|
|
|
| |
21 | VREF | O | Reference voltage output terminal | Not used (open) | |
|
|
|
| ||
22 | EQADJ | I | Center frequency setting terminal for the internal circuit (EQ) | ||
|
|
|
| ||
23 | 3TADJ | I | Center frequency setting terminal for the internal circuit (BPF3T) | ||
|
|
|
|
|
|
24 | VCC | — | Power supply terminal (+3.3V) |
|
|
|
|
|
| ||
25 | WBLADJ | I | Center frequency setting terminal for the internal circuit (BPF22) | ||
|
|
|
| ||
26 | TE | O | Tracking error signal output to the CXD2662R (IC301) | ||
|
|
|
| ||
27 | CSLED | I | Connected to the external capacitor for | ||
|
|
|
| ||
28 | SE | O | Sled error signal output to the CXD2662R (IC301) | ||
|
|
|
|
|
|
29 | ADFM | O | FM signal output of the ADIP |
|
|
|
|
|
| ||
30 | ADIN | I | Receives a ADIP FM signal in AC coupling | ||
|
|
|
| ||
31 | ADAGC | I | Connected to the external capacitor for ADIP AGC | ||
|
|
|
|
| |
32 | ADFG | O | ADIP duplex signal (22.05 kHz ± | 1 kHz) output to the CXD2662R (IC301) | |
|
|
|
| ||
33 | AUX | O | Auxiliary signal (I3 signal/temperature signal) output terminal Not used (open) | ||
|
|
|
| ||
34 | FE | O | Focus error signal output to the CXD2662R (IC301) | ||
|
|
|
| ||
35 | ABCD | O | Light amount signal (ABCD) output to the CXD2662R (IC301) | ||
|
|
|
| ||
36 | BOTM | O | Light amount signal (RF/ABCD) bottom hold output to the CXD2662R (IC301) | ||
|
|
|
| ||
37 | PEAK | O | Light amount signal (RF/ABCD) peak hold output to the CXD2662R (IC301) | ||
|
|
|
| ||
38 | RF | O | Playback EFM RF signal output to the CXD2662R (IC301) | ||
|
|
|
| ||
39 | RFAGC | I | Connected to the external capacitor for RF auto gain control circuit | ||
|
|
|
| ||
40 | AGCI | I | Receives a RF signal in AC coupling | ||
|
|
|
|
| |
41 | COMPO | O | User comparator output terminal | Not used (open) | |
|
|
|
|
| |
42 | COMPP | I | User comparator input terminal | Not used (fixed at “L”) | |
|
|
|
| ||
43 | ADDC | I | Connected to the external capacitor for cutting the low band of the ADIP amplifier | ||
|
|
|
| ||
44 | OPO | O | User operational amplifier output terminal Not used (open) | ||
|
|
|
| ||
45 | OPN | I | User operational amplifier inversion input terminal Not used (fixed at “L”) | ||
|
|
|
|
|
|
46 | RFO | O | RF signal output |
|
|
|
|
|
| ||
47 | MORFI | I | Receives a MO RF signal in AC coupling | ||
|
|
|
|
|
|
48 | MORFO | O | MO RF signal output |
|
|
|
|
|
|
|
|
44
