3
MZ-N707
On power sources
•Use house current , Nickel Cadmium
rechargeable battery, LR6 (SG) battery, or car
battery.
•For use in your house : Use the AC power
adapt or suppl ie d w ith this recorde r. Do not
use any other AC power adaptor since it may
cause the recorder to malfunction.
khACd
Polarity of the
plug

TABLE OF CONTENTS

1. SERVICING NOTES ............................................... 4
2. GENERAL ................................................................... 5

3. DISASSEMBLY

3-1. Disassembly Flow ........................................................... 6
3-2. Case (Lower) ................................................................... 7
3-3. Upper Panel Section........................................................ 7
3-4. LCD Module, Upper Panel Sub Assy ............................. 8
3-5. Mechanism Deck (MT-MZN707-177) ........................... 8
3-6. Set Chassis (5192) Assy.................................................. 9
3-7. MAIN Board ................................................................... 9
3-8. OP Service Assy (LCX-5R) ............................................ 10
3-9. Holder Assy ..................................................................... 11
3-10. DC Motor (Sled) (M602) ................................................ 11
3-11. DC SSM18B Motor (Spindle) (M601),
DC Motor (Over Write Head Up/Down) (M603) .......... 12
4. TEST MODE.............................................................. 13
5. ELECTRICAL ADJUSTMENTS......................... 19

6. DIAGRAMS

6-1. Block Diagram – SERVO/USB Section –...................... 32
6-2. Block Diagram – A UDIO Section –............................... 33
6-3. Block Diagram – DISPLAY/KEY CONTROL/
POWER SUPPLY Section –........................................... 34
6-4. Note for Printed Wiring Board and
Schematic Diagrams ....................................................... 35
6-5. Printed Wiring Board
– MAIN Board (Component Side) –............................. 36
6-6. Printed Wiring Board
– MAIN Board (Conductor Side) –............................... 37
6-7. Schematic Diagram – MAIN Board (1/4) –.................. 38
6-8. Schematic Diagram – MAIN Board (2/4) –.................. 39
6-9. Schematic Diagram – MAIN Board (3/4) –.................. 40
6-10. Schematic Diagram – MAIN Board (4/4) –.................. 41
6-11. IC Pin Function Description ........................................... 48

7. EXPLODED VIEWS

7-1. Upper Panel, Case (Lower) Section ............................... 55
7-2. Chassis Section ............................................................... 56
7-3. MAIN Board Section ...................................................... 57
7-4. Mechanism Deck Section-1 (MT-MZN707-177)........... 58
7-5. Mechanism Deck Section-2 (MT-MZN707-177)........... 59
8. ELECTRICAL PARTS LIST ............................... 60
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous ra-
diation exposure.
Notes on chip component replacement
•Never reuse a disconnected chip component.
•Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
Flexible Circuit Board Repairing
•Keep the temperature of the soldering iron around 270 ˚C dur-
ing repairing.
•Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
•Be careful not to apply force on the conductor when soldering
or unsoldering.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
•Unleaded solder melts at a temperature about 40 ˚C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 ˚C .
Caution: The printed pattern (copper foil) may peel awa y if the
heated tip is applied for too long, so be careful!
•Strong viscosity
Unleaded solder is more viscous (sticky , less prone to flo w) than
ordinary solder so use caution not to let solder bridges occur
such as on IC pins, etc.
•Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.