Sony SLV-469 1 2 3, 1 2 3 4

Additional Information46

EAC-32 Antenna

connector (not

supplied)

Attaching the external

antenna connector

When using a 300-ohm twin lead cable

for a VHF/UHF antenna, use the EAC-

32 antenna connector (not supplied) to

connect the antenna to the VCR.

1Loosen the screws on the antenna connector.

2Wind the twin leads around the screws on the antenna connector.

3Retighten the screws.

300-ohm twin

lead cable

EAC-66

UHF/VHF

band

separator/

mixer (not

supplied)

Attaching a UHF/VHF band

mixer

When using both a 75-ohm coaxial cable

and a 300-ohm twin lead cable for a

VHF/UHF antenna, use the EAC-66

UHF/VHF band separator/mixer (not

supplied) to connect the antenna to the

VCR.

1Loosen the screws on the mixer.

2Wind the twin leads around the screws on the mixer.

3Retighten the screws.

4Connect the 75-ohm coaxial cable to the mixer.

75-ohm coaxial

cable

300-ohm twin

lead cable

General setup information (continued)

Contents

Main Introduction WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. Information For customers in the USA CAUTION NOTE: Table of contents Getting Started Additional Information Basic Operations Additional Operations Unpacking Inserting the batteries Using the remote commander Step 2 Setting up the remote commander Hookups Selecting the best hookup option Step 3 Audio/video (A/V) hookup Antenna hookup Pages 8 and 9 BUse this hookup if youre using a VHF-only antenna (you get channels 213 only) Hookup 1 Hookup 1: VCR setup 2 3 4 Hookup 4Hookup 4 Cable box with many scrambled channels Hookup 2 Hookup 2: VCR setup 2 5 Hookup 3 No cable box, or cable box with only a few scrambled channels Hookup 3: VCR setup 2 5 Hookup 4 Cable box with only a few scrambled channels, using an A/B switch Hookup 4: VCR setup 2 6 5 Step 4 2 Setting the clock 3 4 5 Selecting a language 2 Presetting channels 2 Presetting all receivable channels automatically 3 4 Getting Started Presetting/disabling channels manually 1 2 3 Getting Started Getting Started If the picture is not clear 1 2 channel you want to fine-tune, then press ENTER. Number buttons, ENTER MENU OK >/./?// 3 The fine tuning meter appears. 4 Note that the AFT setting switches to OFF. Playing a tape 1 2 Playing a tape (continued) 3 Turning on the VCR and TV, and starting playback automatically (Trinitron TV Synchro Play) programs 1 2 3 4 5 6 1 Recording TV programs (continued) 2 3 programs using the timer 1 Recording TV programs using the timer (continued) 2 3 4 5 Page Playing/searching at various speeds To resume normal playback Press PLAY. Searching for a selected point on the tape 1 2 To cancel searching Press PLAY or p STOP. To turn off the bar indication Press DISPLAY again. Searching for a selected point on the tape (continued) Skip-searching automatically programs using the quick timer 1 2 Using the quick timer during stop mode Checking/ changing/ canceling timer settings 1 2 3 4 Page Adjusting the picture Adjusting the tracking About Adaptive Picture Control (APC) Changing menu options 1 2 3 Editing with another VCR How to hook up to record on this VCR Operation (when recording on this VCR) Editing with another VCR (continued) 1 2 3 4 General setup information Setting the RF unit 1 2 3 4 1 2 3 Attaching a UHF/VHF band mixer 1 2 3 4 Troubleshooting Symptoms caused by contaminated video heads Troubleshooting (continued) Additional Information Specifications System Tuner section Inputs and outputs Timer section Index to parts and controls Front panel Display window Rear panel Remote commanderRemote commander Page E, F, G, H, I, J, K L, M, N, O P Q Index A, B C D S Q Hookup 3 Hookup 1 Hookup 2