Manuals / Brands / TV and Video / VCR / Sony / TV and Video / VCR

Sony SLV-469 Setting up the remote commander

1 56

Download 56 pages, 766.84 Kb

5

Getting Started

Getting Started

Inserting the batteries

Insert two size AA (R6) batteries by

matching the + and – on the

batteries to the diagram inside the

battery compartment.

Insert the negative (–) end first,

then push in and down until the

positive (+) end clicks into

position.

Using the remote commander

You can use this remote

commander to operate this VCR

and a Sony TV. Buttons on the

remote commander marked with

a dot (•) can be used to operate

your Sony TV.

Step 2

Setting up the remote commander

Remote sensor

Notes

• With normal use, the batteries should last about three to six months.

• If you do not use the remote commander for an extended period of time, remove

the batteries to avoid possible damage from battery leakage.

• Do not use a new battery with an old one.

• Do not use different types of batteries.

To operate

the VCR

a Sony TV

Set TV / VIDEO to

VIDEO and point at the remote sensor on the VCR

TV and point at the remote sensor on the TV

TV / VIDEO

123

Contents

Main Introduction WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. Information For customers in the USA CAUTION NOTE: Table of contents Getting Started Additional Information Basic Operations Additional Operations Unpacking Inserting the batteries Using the remote commander Step 2 Setting up the remote commander Hookups Selecting the best hookup option Step 3 Audio/video (A/V) hookup Antenna hookup Pages 8 and 9 BUse this hookup if youre using a VHF-only antenna (you get channels 213 only) Hookup 1 Hookup 1: VCR setup 2 3 4 Hookup 4Hookup 4 Cable box with many scrambled channels Hookup 2 Hookup 2: VCR setup 2 5 Hookup 3 No cable box, or cable box with only a few scrambled channels Hookup 3: VCR setup 2 5 Hookup 4 Cable box with only a few scrambled channels, using an A/B switch Hookup 4: VCR setup 2 6 5 Step 4 2 Setting the clock 3 4 5 Selecting a language 2 Presetting channels 2 Presetting all receivable channels automatically 3 4 Getting Started Presetting/disabling channels manually 1 2 3 Getting Started Getting Started If the picture is not clear 1 2 channel you want to fine-tune, then press ENTER. Number buttons, ENTER MENU OK >/./?// 3 The fine tuning meter appears. 4 Note that the AFT setting switches to OFF. Playing a tape 1 2 Playing a tape (continued) 3 Turning on the VCR and TV, and starting playback automatically (Trinitron TV Synchro Play) programs 1 2 3 4 5 6 1 Recording TV programs (continued) 2 3 programs using the timer 1 Recording TV programs using the timer (continued) 2 3 4 5 Page Playing/searching at various speeds To resume normal playback Press PLAY. Searching for a selected point on the tape 1 2 To cancel searching Press PLAY or p STOP. To turn off the bar indication Press DISPLAY again. Searching for a selected point on the tape (continued) Skip-searching automatically programs using the quick timer 1 2 Using the quick timer during stop mode Checking/ changing/ canceling timer settings 1 2 3 4 Page Adjusting the picture Adjusting the tracking About Adaptive Picture Control (APC) Changing menu options 1 2 3 Editing with another VCR How to hook up to record on this VCR Operation (when recording on this VCR) Editing with another VCR (continued) 1 2 3 4 General setup information Setting the RF unit 1 2 3 4 1 2 3 Attaching a UHF/VHF band mixer 1 2 3 4 Troubleshooting Symptoms caused by contaminated video heads Troubleshooting (continued) Additional Information Specifications System Tuner section Inputs and outputs Timer section Index to parts and controls Front panel Display window Rear panel Remote commanderRemote commander Page E, F, G, H, I, J, K L, M, N, O P Q Index A, B C D S Q Hookup 3 Hookup 1 Hookup 2