Sony STR-DH510 , Tuner, Control for HDMI

73GB

Additional Information

Recording cannot be carried out.

• Check that the components are connected

correctly.

• Select the source component using the

input buttons (page 35).

The FM reception is poor.

• Use a 75-ohm coaxial cable (not supplied)

to connect the receiver to an outdoor FM

antenna (aerial) as shown below. If you

connect the receiver to an outdoor antenna

(aerial), ground it against lightning. To

prevent a gas explosion, do not connect the

ground (earth) wire to a gas pipe.

Radio stations cannot be tuned in.

• Check that the antennas (aerials) are

connected securely. Adjust the antennas

(aerials) and connect an external antenna

(aerial), if necessary.

• The signal strength of the stations is too

weak (when tuning in with automatic

tuning). Use direct tuning.

• Make sure you set the tuning interval

correctly (when tuning in AM stations

with direct tuning).

• No stations have been preset or the preset

stations have been cleared (when tuning

by scanning preset stations). Preset the

stations (page 40).

• Press DISPLAY repeatedly so that the

frequency appears on the display.

RDS does not work.*

•Make sure that you are tuned to an FM

RDS station.

• Select a stronger FM station.

The RDS information that you want

does not appear.*

•Contact the radio station and find out

whether they actually provide the service

in question. If so, the service may be

temporarily out of order.

*Models of area code ECE, CEK, AU1 only.

The Control for HDMI function does not

work.

•Check the HDMI connection (page 23).

•Make sure “CTRL.HDMI” is set to

“CTRL ON” in the HDMI menu (page

58).

•Make sure the connected component is

compatible with the Control for HDMI

function.

•Check the Control for HDMI settings on

the connected component. Refer to the

operating instructions of the connected

component.

•Repeat the procedures of “Preparing for

the “BRAVIA” Sync” if you change the

HDMI connection, connect/disconnect the

AC power cord (mains lead), or when

there is a power failure (page 47).

Tuner

AM

ANTENNA

Receiver

To ground

Ground (earth)

wire (not supplied)

Outdoor FM antenna (aerial)

Control for HDMI

continued

Contents

Main To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. For customers in the United States WARNING Owners Record Important Safety Instructions CAUTION For customers in Europe For customers in Australia About This Manual On Copyrights About area codes Table of Contents Connections Preparing the Receiver Basic Operations Tuner Operations Supplied accessories Description and location of parts Front panel 54312 qs 89q;qa 67 Indicators on the display q; 9 8 1234 56 7 Page Rear panel 6 5 1 132 1, 2 4 AAudio signal section Remote commander Using the SHIFT (Q) and TV (R) button To control the receiver To control a Sony TV Press and hold TV (R) and then press the yellow printing button to select the function you want. Page To control other Sony components Inserting batteries into the remote 1: Installing the speakers Example of a 5.1 channel speaker system configuration Connections Note Tips 2: Connecting the speakers Before connecting the cords, be sure to disconnect the AC power cord (mains lead). Subwoofer*Surround speaker LeftRight FRONT 3: Connecting the TV Before connecting cords, be sure to disconnect the AC power cord (mains lead). b) a) CE Tip 4a: Connecting the audio components Notes on connecting DIGITAL MEDIA PORT adapter BVideo cord (not supplied) To detach the DIGITAL MEDIA PORT adapter from DMPORT jack 4b: Connecting the video components If you want to connect several digital components, but cannot find an unused input HDMI features Components to be connected Connecting components with HDMI jacks AAA AHDMI cable (not supplied) Notes on connecting cables Notes on HDMI connections The following illustration shows how to connect a DVD player or DVD recorder. ACoaxial digital cord (not supplied) Connecting a DVD player, DVD recorder AD B*C DVD player, DVD recorder Audio signals Video signals Connecting a Satellite tuner, Cable TV tuner BA CD SAT Video signalsAudio signals D Connecting components with analog video and audio jack VCR, DVD recorder Audio signals Video signals AVideo cord (not supplied) BAudio cord (not supplied) 5: Connecting the antennas (aerials) To the wall outlet FRONT 6: Connecting the AC power cord (mains lead) Connect the AC power cord (mains lead) to a wall outlet. Initializing the receiver 1 receiver. 2 Calibrating the appropriate speaker settings automatically 1 microphone to the AUTO CAL MIC jack. 2 microphone. 2 Error and warning codes To cancel Auto Calibration After you have finished When error codes appear To rectify the error Error codes and remedies When warning codes appear To change the settings manually 1 2 3 4 5 Adjusting the speaker levels (TEST TONE) 2 LEVEL, then press or b. 3 Playback 1 4 2 3 5 1 to select the input you want to create an index name for. 2 3 SYSTEM, then press or b. 4 Using the Sleep Timer media 2 3 4 Listening to FM/AM radio 1 select the FM or AM band. 2 Using the controls on the receiver 1 2 3 4 If you cannot tune in a station 1 2 3 Tuning into a station directly (Direct Tuning) Changing the AM tuning scale Presetting FM/AM radio stations 1 2 3 4 1 Naming preset stations 2 Using the controls on the receiver 1 2 3 4 5 6 Using the Radio Data System (RDS) (Models of area code ECE, CEK, AU1 only) 2 channel sound mode Receiving RDS broadcasts Selecting the sound field xA.DIRECT (Analog direct) Movie mode xA.F.D. AUTO (A.F.D. Auto) xMULTI ST. (Multi Stereo) When headphones are connected Page Page What is BRAVIA Sync? Preparing for the BRAVIA Sync If your TV is compatible with the Control for HDMI-Easy Setting function 1 2 Playing back components with one-touch operation (One-Touch Play) Enjoying the TV sound from the speakers connected to the receiver Sets System Audio (System Audio Control) Turns on (if in Control to on standby mode) Switches to appropriate HDMI input Minimizes TV Outputs TV volume sound Turning off the receiver with the TV (System Power Off) Press and hold TV, then press TV ?/1. Enjoying movies with the optimum sound field (Theater/Theatre Mode Sync) Enjoying the TV sound via an HDMI cable (Audio Return Channel) 2 Switching between digital and analog audio Advanced Operations (INPUT MODE) 1 2 Enjoying the sound from other inputs 2 3 4 5 Assigning input jacks Enjoying sound/images from the components connected to the DIGITAL MEDIA PORT 1 2 component. Using the setting menu Overview of the menus Advanced Operations Page (Models of area code ECE, CEK, AU1 only ) LEVEL menu xT. TON E Adjusting the speaker level SPEAKER menu 3/2 1. xFRT SIZE xCNT SIZE xSUR SIZE xFL DIST. xFR DIST. xCNT DIST. SURROUND menu EQ menu xFM MODE xNAME IN xA/V SYNC xDUAL HDMI menu xCTRL.HDMI xPASS.THRU xAUDIO.O UT xSW LEVEL SYSTEM menu xSW L.P.F. xARC Changing the input button assignments 1 button of which you want to change the assignment, hold down AV ?/1. 2 release the input button you selected in step 1. Clearing all the contents of the remotes memory 2 RM-AAU071 only RM-AAU074 only Glossary xDeep Colour (Deep Color) xDigital Cinema Sound (DCS) xDolby Digital xDolby Pro Logic II xDolby Surround (Dolby Pro Logic) Precautions On safety On power sources On heat buildup On placement Troubleshooting Audio Page Video Tuner Control for HDMI Remote commander Others Error messages Specifications FM tuner section AM tuner section Video section General Design and specifications are subject to change without notice. Index