TRIDENT PROTECTlON CIRCUITRY
Your Rubicon amplifier is protected against both overheating and short circuits by means of main power fuses and the following circuits:
+Auto High Current power supply
+Sneaker Output Protection
+Ground Fault Differential
+Smart Power Supply Thermal Rollback & a Thermal Protection Circuit
r NOTE: If you experience blown main power supply fuses, it is like@ 
that the amplifier is seeing a dead shorf, either in the speaker wire or in the speaker itself. Rectify the problem before blowing muttiple fuses! DO NOT increase values beyond fhe original fuse value! Doing so will void your warrant and may damage your amplifer.
TROUBLESHOOTING
|
|
|
| |
PROBLEM | CAUSE | |||
|
|
|
| |
|
| 1. No power or ground at the amp. | ||
No Sound and power LED is not lit | 2. No remote | |||
|
| 3. Blown fuse near the battery | ||
|
|
|
| |
|
| 1. No signal input | ||
No sound, power LED is lit. | 2. The AlRBASS/Accessory switch | |||
is in the “IN”position. Move it to the | ||||
|
| |||
|
| “OUT” position. | ||
|
|
|
| |
Repeatedly blow amp fuse; | 1. Speaker or leads may be shorted | |||
frequent activation of Smart Power | ||||
2. Verify adequate amp ventilation | ||||
Supply Circuit | ||||
|
| |||
|
|
|
| |
Not enough input sensitivity while | Be sure both Left and Right input | |||
signal switches are set to the “BAL” | ||||
using the Balanced Input | ||||
position. | ||||
|
| |||
|
|
|
| |
Very little output, or output is | Make sure that both the L.P. and | |||
the H.P. crossvers aren’t | ||||
muffled. | ||||
engaged | ||||
|
| |||
|
|
|
| |
|
| Output signal level is too high and | ||
Left and Right “Clip” indicators | the amplifier output is clipping. | |||
lighting | Reduce the level either at the source | |||
|
| or at the input level controls. | ||
|
|
|
| |
|
| 1. Make sure the Right Input Signal | ||
|
| Switch is in the “UNBAL” position. | ||
Alternator whine while using | 2. Try the Left Input Signal switch | |||
in the “BAL” and “UNBAL” position: | ||||
Unbalanced RCA inputs | ||||
leave the switch in the quietest | ||||
|
| |||
|
| setting. This will not effect the | ||
|
| performance of the amplifier. | ||
|
|
|
| |
SERVICE
Your Soundstream RUBICON amplifier is protected by a limited warranty. Please read the enclosed warranty card for details.
POWER |
| / | 4 R Stereo | 2 n Stereo |
| 1 R Stereo |
| Maximum | |
’ | (8 fi Bridged) | (4 n Bridged) |
| (2 R Bridged) |
| Rated | |||
|
| (12.6 Vdc) | (14.4 Vdc) |
| (14.4 Vdc) |
| output | ||
502 |
|
| 1oow | x2 | 250w x 2 |
| 250w x 2 |
| 500 Watts |
|
| (2OOW | x 1 ) | (5OOW x 1) |
| (5OOW x 1) |
| ||
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
| 700 Watts |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 1000 Watts |
|
|
|
|
|
|
|
|
|
|
THD |
|
| <O.l% |
|
|
| |||
Signal to Noise |
| A00 dB |
|
|
| ||||
Frequency | Response | 20 Hz to 20 kHz * 0.5 dB |
| ||||||
Stereo Separation | >90 dB |
|
|
| |||||
Damping |
|
| >200 |
|
|
|
| ||
input Sensitivity |
| 300 mV to 5.0 Volts |
| ||||||
Input Impedance | 10k Ohms |
|
|
| |||||
Crossover Specifications
Low Pass: 55 Hz - 220 Hz at 24 dB/Octave
High Pass: 70 Hz - 160 Hz at 12 dB/Octave
Hawkins Bass Control
Sub Sonic Filter: No boost, High Pass filter from 13 to 30 Hz.
Hawkins Bass Control: 0 to +9 dB Boost; Boost and Sub Sonic filter, variable from 30 to 70 Hz.
Dimensions (W x D x H)
RUB CON502: 11 .O” X 9.8” X 2.25”
RUB CON702: 13.0” X 9.8” X 2.25”
RUB CON1002: 15.0” X 9.8” X 2.25”
18 | 19 |
