Manuals
/
SPX Cooling Technologies
/
Kitchen Appliance
/
Refrigerator
SPX Cooling Technologies
MHF702 user manual Marley MH Fluid Cooler, User Manual sea05-116E
Models:
MHF702
MHF705
1
1
36
36
Download
36 pages
60.66 Kb
1
2
3
4
5
6
7
8
<
>
Troubleshooting
Install
Maintenance
Motor Wiring
Those are only some of the safety issues that may arise in the design
Slushy, transitory ice forms routinely in the colder regions of the fill of low temperature towers, and is visible through the tower louvers. Such ice normally has no adverse effect on fluid cooler operation, but its appearance should be a signal to the operator to undertake ice control procedures
Fluid Cooler Cleaning
How to
Safety
SPX Cooling Technologies Services
Page 1
Image 1
/
Marley MH
Fluid Cooler
/
User Manual
sea_05-116E
Page 2
Page 1
Image 1
Page 2
Contents
User Manual sea05-116E
Marley MH Fluid Cooler
Page
Contents
Preparation
Safety First
Itisnot intended nor assumed that access tothe fan deck onsingle-flow
Fluid Cooler Location
Those are only some of the safety issues that may arise in the design
to be sure that all safety considerations have been addressed
Tower Shipment
Installation
Receiving Fluid Cooler
Hoisting Fluid Cooler
Installation
Fluid Cooler Installation
When using a starter
Motor Wiring
Installation
When using a VFD
When using a two-speed starter
Installation
Before beginning, ensure that the motor is rated for “Inverter Duty”
Improper use of a VFD may cause damage to equipment or personal injury. Failure to correctly install the VFD drive will automatically void all warranties associated with the motor and any equipment that is either electrically or mechanically directly attached to the VFD drive system. The length of this warranty avoidance will be contingent on properly installing the VFD system and repairing any damage that may have occurred during its operation. SPX Cooling Technologies does not assume responsibility for any technical support or damages for problems associate with non-Marley brand VFD systems
Installation
Installation
Mechanical Equipment
10 - 60 hrs. of operation. See Bushing Fastener Torque Values on page
Installation
Fluid Cooler Start-Up
Operation
Water System
7. While operating the recirculating water pumps and prior to operat- ing the cooling tower fan, execute one of the two alternative biocidal treatment programs described in the following
Operation
General
Fluid Cooler Operation
Operation
Operation
Wintertime Operation
fan acceleration time of 30 seconds per hour
Operation
Slushy, transitory ice forms routinely in the colder regions of the fill of low temperature towers, and is visible through the tower louvers. Such ice normally has no adverse effect on fluid cooler operation, but its appearance should be a signal to the operator to undertake ice control procedures
Protection Against Coil Freezing
Intermittent Wintertime Operation
Operation
Draining the coil is not acceptable as a normal method of freeze
Operation
Water Treatment and Blowdown
Maintenance
Maintaining Water Quality
Blowdown
Fluid Cooler Cleaning
Maintenance
Maintenance
Belt Tensioning
When water treatment chemicals are added, they should not be in
MOTOR
JACKING SCREWS
SINGLE MOTOR-TWO FANS
JACKING SCREWS MOTOR
Maintenance
Sheave Alignment
FAN SHAFT SHEAVE
STRAIGHT EDGE
Bushing Fastener Torque Values
Fluid Cooler Maintenance
Maintenance
Semi-Annually If equipped, check the belt tension and condition
Maintenance
Maintenance
Motor Relubrication Instructions
Open and lock out disconnect switch to make certain motor cannot
oil designed specifically for these Geareducers. If, after five years
Maintenance
Seasonal Shutdown Instructions
on page
Maintenance
Prolonged Shutdown
Maintenance
SPX Cooling Technologies Services
Maintenance Service
Maintenance Schedule
Monthly
Semi-annually
Trouble
Troubleshooting
Cause
Remedy
Trouble
Troubleshooting
Cause
Remedy
Additional Information
Page
SPX COOLING TECHNOLOGIES MALAYSIA Sdn Bhd
seaM05-116E