Manuals
/
SPX Cooling Technologies
/
Kitchen Appliance
/
Refrigerator
SPX Cooling Technologies
MHF702, MHF705 user manual
Models:
MHF702
MHF705
1
35
36
36
Download
36 pages
60.66 Kb
29
30
31
32
33
34
35
36
<
>
Troubleshooting
Install
Maintenance
Motor Wiring
Those are only some of the safety issues that may arise in the design
Slushy, transitory ice forms routinely in the colder regions of the fill of low temperature towers, and is visible through the tower louvers. Such ice normally has no adverse effect on fluid cooler operation, but its appearance should be a signal to the operator to undertake ice control procedures
Fluid Cooler Cleaning
How to
Safety
SPX Cooling Technologies Services
Page 35
Image 35
Page 34
Page 36
Page 35
Image 35
Page 34
Page 36
Contents
User Manual sea05-116E
Marley MH Fluid Cooler
Page
Contents
Preparation
Safety First
to be sure that all safety considerations have been addressed
Fluid Cooler Location
Itisnot intended nor assumed that access tothe fan deck onsingle-flow
Those are only some of the safety issues that may arise in the design
Hoisting Fluid Cooler
Installation
Tower Shipment
Receiving Fluid Cooler
Installation
Fluid Cooler Installation
Installation
Motor Wiring
When using a starter
Before beginning, ensure that the motor is rated for “Inverter Duty”
When using a two-speed starter
When using a VFD
Installation
Improper use of a VFD may cause damage to equipment or personal injury. Failure to correctly install the VFD drive will automatically void all warranties associated with the motor and any equipment that is either electrically or mechanically directly attached to the VFD drive system. The length of this warranty avoidance will be contingent on properly installing the VFD system and repairing any damage that may have occurred during its operation. SPX Cooling Technologies does not assume responsibility for any technical support or damages for problems associate with non-Marley brand VFD systems
Installation
Installation
Mechanical Equipment
10 - 60 hrs. of operation. See Bushing Fastener Torque Values on page
Installation
Water System
Operation
Fluid Cooler Start-Up
7. While operating the recirculating water pumps and prior to operat- ing the cooling tower fan, execute one of the two alternative biocidal treatment programs described in the following
Operation
Operation
Fluid Cooler Operation
General
fan acceleration time of 30 seconds per hour
Wintertime Operation
Operation
Operation
Slushy, transitory ice forms routinely in the colder regions of the fill of low temperature towers, and is visible through the tower louvers. Such ice normally has no adverse effect on fluid cooler operation, but its appearance should be a signal to the operator to undertake ice control procedures
Operation
Intermittent Wintertime Operation
Protection Against Coil Freezing
Draining the coil is not acceptable as a normal method of freeze
Operation
Maintaining Water Quality
Maintenance
Water Treatment and Blowdown
Maintenance
Fluid Cooler Cleaning
Blowdown
When water treatment chemicals are added, they should not be in
Belt Tensioning
Maintenance
JACKING SCREWS MOTOR
JACKING SCREWS
MOTOR
SINGLE MOTOR-TWO FANS
STRAIGHT EDGE
Sheave Alignment
Maintenance
FAN SHAFT SHEAVE
Maintenance
Fluid Cooler Maintenance
Bushing Fastener Torque Values
Semi-Annually If equipped, check the belt tension and condition
Maintenance
oil designed specifically for these Geareducers. If, after five years
Motor Relubrication Instructions
Maintenance
Open and lock out disconnect switch to make certain motor cannot
on page
Seasonal Shutdown Instructions
Maintenance
Maintenance
Prolonged Shutdown
Maintenance
SPX Cooling Technologies Services
Semi-annually
Maintenance Schedule
Maintenance Service
Monthly
Remedy
Troubleshooting
Trouble
Cause
Remedy
Troubleshooting
Trouble
Cause
Additional Information
Page
SPX COOLING TECHNOLOGIES MALAYSIA Sdn Bhd
seaM05-116E