SSS BSE 650-0 manual Defining control buttons for actuation of the BSE

the buttons BTS/BTC 750-... and BTLM 650-... for actuation can be manually programmed. For pro- gramming a key and an LED as a status display and functional testing are available.

Defining control buttons for actuation of the BSE 650-... .

Important!

There is no BTLM 650-... or BTLE 050-... activated. The

BSE 650-... can only be programmed when the YR system is active.

Switch BSG 650-... to the pro- gramming mode;

The status LED at the BSG 650-...

flashes evenly. Fig. 2

Switch the BSE 650-... you wish to program to the programming mode;

The status LED flashes very slowly. Fig. 3

Pick up the receiver of the BTS/BTC 750-... at which you wish to program a button;

The call connected signal sounds. Fig. 4

Press the button you wish to program;

An acknowledgement tone sounds in the receiver. Replace the receiver. Fig. 5

If you wish this BSE 650-... to be actuated from several BTS/BTC 750-... units, repeat the

steps described for Fig. 4 and 5 until all the telephones / BTLM units are programmed.

Switch off the programming mode at the BSG 650-... ;

Status LED is extinguished, opera- ting status of the overall system. Fig. 6

or process other programming points.

Defining call buttons for actua- tion of the BSE 650-... which actuate the BSE 650-... with the function „secondary signal con- troller“ in parallel to a BTS/BTC 750-... .

Important!

No BTLM 650-... or BTLE 051-... is active.

If you wish for an additional signal to be issued when actuating the call button, in parallel to the call signal at the BTS/BTC 750-..., the swit- ching contact in the BSE 650-... can be used for actuation.

However, the call button at the door loudspeaker must already be pre- viously assigned to the relevant BTS/BTC 750-... .

At a BSE 650-... either a control function or a parallel connected NSC function can be programmed. Double assignment is not possible.

Switch the BSG 650-... to the programming mode;

The status LED flashes evenly. Fig. 2

Switch the BSE 650-... you wish to program to the programming mode;

The status LED flashes very slowly. Fig. 3

Press the call button you wish to program at the door loudspea- ker;

The status LED at the BSE 650-...

briefly flashes faster and the door call sounds at the parallel BTS/BTC 750-... .

Fig. 7

Switch off the programming

mode at the BSG 650-...

The status LED goes out, operating status of the overall system.

Fig. 6

or process other programming points.

Deleting the control button for actuation of the BSE 650-... .

Buttons which act on a BSE 650-...

are generally individually deleted, i.e. when the BSE is in the delete mode, each button you wish to delete must be selectively accessed and deleted.

Call buttons with NSC function can only be overwritten. In order to delete a button programmed with an NSC function, this must first be overwritten with a button at the BTS/BTC750-... (control function). The key can subsequently be dele- ted.

Switch the BSG 650-... to the programming mode;

(if not already switched on) The status LED flashes evenly. Fig. 2

Switch the BSE 650-... you wish to program to the programming mode;

The status LED flashes very slowly. Fig. 3

Switch the BSE 650-... to the delete mode;

The status LED stays alight

Fig. 8

Lift the receiver at the BTS/BTC 750-... from which you wish to delete the button;

The call connected tone sounds. Fig. 4

Press the button you wish to delete;

You will hear an acknowledgement tone in the receiver. If you wish to delete the button in several BTS/BTC 750-... units which actuate this BSE 650-... , repeat the steps described under Fig. 4 and Fig. 5 until all telephone buttons have been deleted.

Fig. 5

6