TROUBLESHOOTING

If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem.

When diagnosing faults in operation of the tool, always check that the hydraulic power source is supplying the cor- rect hydraulic flow and pressure to the tool as listed in the table. Use a flowmeter known to be accurate. Check the flow with the hydraulic oil temperature at least 80 °F/27 °C.

SYMPTOM

CAUSE

SOLUTION

Tool does not run.

Hydraulic power source not

Check power source for proper flow and

 

functioning correctly.

pressure (7–9 gpm 26–34 lpm at 2000

 

 

psi/140 bar.

 

Coupler or hoses blocked.

Remove obstruction.

 

Mechanical failure.

Have tool serviced by authorized dealer.

Tool runs backwards.

Pressure and return lines incorrectly

Correct hose connections. Motor shaft

 

connected.

rotates counterclockwise as viewed from

 

 

the end of the motor shaft.

Diamond saw cuts slow.

Insufficient fluid flow or too high

Check hydraulic supply. If hydraulic

 

back pressure or relief valve set too

supply is correct, have unit serviced by

 

low.

authorized dealer.

 

Back pressure too high.

Should not exceed 250 psi/17 bar at 9

 

 

gpm/34 lpm measured at the end of the

 

 

tools operating hoses.

 

Loss of diamond segment side

Replace chain.

 

clearance.

 

 

Chain segment dulled because of

Redress segmented by cutting in

 

continuous use in hard material or

abrasive material (i.e. concrete, building

 

rebar.

block, etc.). NOTE: This indicates that

 

 

the wrong chain is being used.

 

Wrong chain for application.

Scale down to a lower numbered chain.

 

Wired edged bar rails.

Dress rails square.

 

Hydraulic fluid mixed in water

Have tool serviced.

 

supply.

 

Excessive vibration and cuts

Segment(s) broken or missing.

Repair broken segment or replace chain.

rough.

 

 

Chain installed backwards.

Correct chain direction.

 

Loose chain tension.

Re-tension the chain.

 

Excessive feed force.

Reduce feed force.

Will not cut straight.

Accumulated saw bar wear and

Turn the saw bar over and dress rails

 

uneven chain segment profile wear.

square. Replace the saw bar and chain.

Loss of power.

Drive sprocket slipping on

Adjust and tighten Trantorque® adapter

 

Trantorque® adapter.

to 17 ft lb/23 Nm.

Trigger hard to press.

Pressure and return hose reversed.

Connect for proper flow direction. Motor

 

 

shaft must rotate clockwise.

 

Back-pressure too high.

Should not exceed 250 psi/17 bar @ 9

 

 

gpm/34 lpm measured at the end of the

 

 

tool’s operating hoses.

20 ► DS06 User Manual

Page 19 Page 21
Page 20
Image 20
Stanley Black & Decker DS06 user manual Troubleshooting, Symptom Cause Solution
Page 19 Page 21

DS06 specifications

Stanley Black & Decker DS06 is a powerful and versatile tool that combines cutting-edge technology with user-friendly features, making it a must-have for both professionals and DIY enthusiasts. Designed for optimal performance, the DS06 caters to a wide range of applications, from heavy-duty construction tasks to light home improvement projects.

One of the standout features of the DS06 is its robust motor. With a high power output, this tool delivers consistent performance, ensuring that users can tackle even the toughest materials with ease. The motor's efficiency not only enhances the tool's performance but also contributes to its longevity, allowing it to withstand rigorous use in demanding environments.

In addition to its powerful motor, the DS06 incorporates advanced battery technology. Equipped with a lithium-ion battery, this tool promises an extended runtime and reduced charging times compared to traditional batteries. Users can experience greater convenience, as the quick-charge capability means less downtime and more productivity. The battery's lightweight design also enhances the tool's overall ergonomics, making it more comfortable to handle during extended use.

Another significant characteristic of the DS06 is its intelligent design. Featuring an ergonomic grip, the tool is designed to reduce user fatigue, making it suitable for prolonged tasks. The lightweight construction of the DS06 ensures that users can maneuver the tool easily without compromising control.

Stanley Black & Decker has also prioritized safety with the DS06. It includes several safety features, such as a blade guard and a safety lock-off switch, which help prevent accidents during operation. These features provide peace of mind, allowing users to focus on their work without worrying about potential hazards.

Versatility is a key attribute of the DS06, with its ability to accommodate various attachments and accessories. This adaptability makes it a valuable addition to any tool collection, as it can be used for a wide array of tasks, including cutting, sanding, and drilling.

In summary, the Stanley Black & Decker DS06 is a tool that exemplifies innovation and practicality. Its powerful motor, advanced battery technology, ergonomic design, and safety features make it an ideal choice for a diverse range of applications. Whether you're a professional contractor or a weekend warrior, the DS06 is equipped to meet your needs and elevate your work efficiency.
Top Page Image Contents