ENGLISH
5MAINTENANCE
5.1Preparation
All service and all maintenance must be carried out on a stationary machine with the engine switched off.
Prevent the machine from rolling by al- ways applying the parking brake.
Stop the engine.
Prevent unintentional starting of the engine by disconnecting the spark plug cable from the spark plug and remov- ing the ignition key.
5.2 Washing position
1.Activate the parking brake.
2.Set the implement lifter in transport position.
92/107 M: Lift up the rear section of the cutting deck, undo the catches (12:L) and lower.
121 M: Disconnect the rear section of the cut- ting deck by removing the pins (7:I).
6.Remove the belt cover. See fig. 5:E, 8 and 10. The number in the figure indicates the key width.
7.Only 110/125 Combi Pro: Remove the belt guide (5:F).
8.Grip the belt tensioner’s lever with your left hand. Pull the lever and unhook the tensioner from the belt with your right hand. See fig. 16.
9.Force the belt off the deck’s pulley.
10.Grip the front edge of the deck and lift up. Lift until the deck is completely vertical and rest the rear edge on the floor. See fig. 24.
Reset 110/125 Combi Pro in accordance with 3.1. Reset 107 M HD in accordance with 3.2.
Reset 92/107 M in accordance with 3.3. Reset 121 M in accordance with 3.2.
3.Set the highest cutting height.
4.110/125 Combi Pro, 107 M HD, 121 M: Disconnect the rear section of the cutting deck by removing pins and any washers. See fig. 2, 7:I and 13.
92/107 M: Lift up the rear section of the cutting deck, undo the catches (12:L) and lower.
5.Grip the front edge of the deck and lift up. Hook on the chain so that the deck is pointing diago- nally upwards. See fig.
5.4 Cleaning
The underside of the deck must be cleaned after each use.
Set the deck in washing position.
Clean the underside of the deck carefully. Use a
It is absolutely forbidden to start the engine when the deck is in the washing position.
Reset 110/125 Combi Pro in accordance with 3.1.1, point 8.
Reset 107 M HD in accordance with 3.2.1, point 7. Reset 121 M in accordance with 3.2.1, point 7. Reset 92/107 M in accordance with 3.3.1, point 7.
5.5 Wheels
110/125 Combi Pro is fitted with two lubricating cups (25:O) for the vertical shafts.
107 M HD is fitted with two lubricating cups for the vertical shafts (26:O) and two lubricating cups (26:N) for the wheel axles.
The grease nipples must be lubricated with univer- sal grease after 50 hours of operation.
5.3 Service position
1.Activate the parking brake.
2.Set the implement lifter in transport position.
3.110/125 Combi Pro, 92/107 M: Set the highest cutting height.
107 M HD, 121 M: Set the cutting height in the centre position.
4.If the deck has electrical cutting height adjust- ment, disconnect the cable from the machine. See fig. 15.
5.110/125 Combi Pro:
Remove pins and washers. See fig. 2.
107 M HD:
Remove pins and washers. See fig. 13.
5.6 Replacing blades
Wear protective gloves when changing blade(s) to avoid cutting yourself.
Check that the blades are always sharp. This produces the best cutting results.
Always check the blade(s) after a collision. If the blade system has been damaged, defective parts should be replaced.
Always use genuine spare parts. Non- genuine spare parts can entail a risk of injury, even if they fit the machine.
The deck is equipped with blades according to the following alternatives:
•Separate blades, screwed into place on the blade bars. See fig. 27.
•Full blade. See fig.
37
