Attention: Danger! Rotating machinery.
8.The hedge trimmer should always be held with both hands.
9.Before using the equipment clear the working area of any foreign objects and be aware of foreign objects during operation of the machine! If the machine becomes jammed e.g. by thick branches, switch off and disconnect the machine from the mains socket before investigating and rectifying the cause of the jam. Take special care when switching the machine on again.
10.Check the flex and all connections for any visible faults before using the machine (plug discon- nected). Do not use a faulty flex.
11.Keep the flex away from the cutting area.
12.Do not use the trimmer in wet weather and do not use it to cut wet hedges.Do not wash down the device with water. Do not use any high- pressure cleaning devices or steam jet devices for cleaning.
13.Carry the trimmer by the handles provided and keep hands away from the cutting blades.
14.In line with agricultural Trade Association Regu- lations only persons over the age of 17 may work on their own with electric hedge trimmers. Use is permitted for persons over 16 years if the work is carried out under the supervision of adults.
15.We would recommend that safety clothing is worn during the work and that eyes, ears, hair, hands and feet are fully protected. Protective gloves should also be worn.
16.Ensure that the motor of your hedge shears can not be switched on by mistake when you put it down after work or when you are going to clean the device. Never forget to unplug the mains supply!
17.Check the cutting unit regularly for damage and if damage is discovered, the cutting unit should be properly repaired.
18.Be aware of your responsibility as user towards third parties in the working area.
19.The trimmer must be properly checked and serviced. If the blades get damaged they should only be exchanged in pairs. In the event of damage from impact, specialist’s inspection is essential.
20.Only use extension cords that are approved for outdoor use and that are not lighter than rubber tube cords type H07
21.Do not use the cable for purposes it has not been designed for. Never carry a power tool at its cable. Do not pull out the plug from the socket using the cable. Protect the cable from heat, oil and sharp edges.
22.Ensure that the equipment is stored safely after use in such a way that the blade cannot be touched.
23.When using the equipment, hold it securely with both hands, stand firmly and ensure that you have sufficient working space. There should be no people, animals or objects within the working area. Select the cutting height so that the blade does not make contact with the ground and you can operate the equipment from a secure position.
24.Take care when transporting the equipment (only with blade cover!).
25.For initial use of the hedge trimmer we would recommend that in addition to reading the oper- ating instructions, you also seek a practical demonstration from an expert.
26.Always ensure that all protective devices and handles are properly fitted.
27.Never try to use an incomplete tool or a tool that has been modified in a way that has not been approved.
28.Do not allow children to use a power tool.
29.The use of the hedge trimmer is to be avoided if other persons, above all children, are within the working area.
30.Familiarize yourself with the working area and pay attention to possible dangers which you might not be able to hear due to the noise of the machine.
31.Always pay attention. Take care of what you do. Do your work sensibly. Do not use a power tool if you cannot concentrate.
32.ATTENTION ! Only use the accessories or attach- ments shown in the Operating Instructions. The use of other
33.Have your power tools repaired by an appro- priately qualified electrician only. This power tool complies with the applicable safety regulations. Repairs must only be carried out by qualified electricians using original spare parts; otherwise, accidents may occur to the user.
5. Before use
Safety Guard (Fig. 2)
Push the supplied hand guard (3) over the blades and fix securely with each 2 screws on both sides of the housing according to fig. 2. The safety shield prevents touching the blades during operation. Hold tool with both hands!
Power connection
The machine can only be connected to a
Power Circuit Breaker
Machines which will be used in different outside loca- tions must be connected to a Power Circuit Breaker.
Securing the extension lead (Fig. 3)
Only use extension leads suitable for outside use. The cross section of the wire (max. length of extension cord: 75m) must be at least 1,5 mm². Secure the connection between the device’s power cord and the extension cable by leading the extension cable through the strain relief in the housing (Fig. 3).
