Outdoor Installation

Install the generator in a area that is free of debris, bystanders, and overhead obstructions. Make sure the generator is on secure level ground so that it cannot slide or shift around. Also install the generator in a manner so that the exhaust will not be discharged in the direction of nearby homes.

The installation site must be relatively free from moisture and dust. All electrical equipment should be protected from excessive moisture. Failure to do will result in deterioration of the insulation and will result in short circuits and grounding.

Foreign materials such as dust, sand, lint and abrasive materials have a tendency to cause excessive wear to engine and alternator parts.

CAUTION

Pay close attention to ventilation when operating the generator inside tunnels and caves. The engine exhaust contains noxious elements.

Mounting

The generator should always be mounted on a flat level surface to isolate vibration of the generator when it is running. DO NOT place the generator on slopes, the possibility exists that the generator could slide.

STOW G-4.5R — INSTALLATION

Indoor Installation

Exhaust gases from gasoline engines are extremely poisonous. Whenever an engine is installed indoors the exhaust fumes must be vented to the outside. The engine should be installed at least two feet from any outside wall. Using an exhaust pipe which is too long or too small can cause excessive back pressure which will cause the engine to heat excessively and possibly burn the valves.

Eliminate the danger of deadly carbon monoxide gas. Remember that exhaust fumes from any gasoline engine are very poisonous if discharged in a closed room, but harmless if allowed to mix with the outside air.If the generator is installed indoors, you must make provisions for venting the engine exhaust to the outside of the building.

Generator Grounding

To guard against electrical shock and possible damage to the equipment, it is important to provide a good EARTH ground. Always use the ground terminal on the generator to ground the generator.

Article 250 (Grounding) of the National Electrical Code (NEC) provides guide lines for proper grounding and specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.

NEC articles 250-64(b) and 250-66 set the following grounding requirements:

1.Use one of the following wire types to connect the generator to earth ground.

a.Copper - 10 AWG (5.3 mm2) or larger.

b.Aluminum - 8 AWG (8.4 mm2) or larger.

2.When grounding the generator (Figure 3) connect the ground cable between the lock washer and the nut on the generator and tighten the nut fully. Connect the other end of the ground cable to earth ground.

3.NEC article 250-52(c) specifies that the earth ground rod should be buried a minimum of 8 ft. into the ground.

STOW G-4.5R A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #3 (03/13/06) — PAGE 23

Page 22 Page 24
Page 23
Image 23
Stow manual Stow G-4.5R Installation, Outdoor Installation, Mounting, Indoor Installation, Generator Grounding
Page 22 Page 24

G-4.5R specifications

The Stow G-4.5R is an exceptional piece of rugged engineering designed for professionals who require efficiency and reliability in demanding environments. This cutting-edge equipment stands out for its unique combination of robust features and innovative technologies.

At the heart of the G-4.5R is its powerful engine, designed to facilitate high-performance operations. The machine is equipped with a fuel-efficient powertrain that not only maximizes output but also minimizes consumption. This feature is crucial for users who need to operate over extended periods without frequent refueling, making the G-4.5R highly suitable for long-term projects.

The G-4.5R boasts an advanced hydraulic system that enhances its lifting capabilities. With optimized hydraulic mechanics, the machine can handle heavier loads with improved precision and speed. This ensures that users can perform tasks more efficiently, reducing downtime and increasing productivity. Furthermore, the hydraulic system is complemented by a robust frame, designed to withstand rigorous field conditions while providing stability during operation.

Another notable aspect of the Stow G-4.5R is its user-centric design. The operational interface is intuitively laid out, allowing users to easily navigate controls and features without extensive training. The ergonomic design of the operating cabin further enhances comfort, reducing fatigue during long working hours. Noise reduction technologies have also been integrated into the design, making the working environment more pleasant.

In terms of technology, the G-4.5R features real-time monitoring systems that provide crucial operational data. These systems allow users to track fuel levels, hydraulic pressures, and performance metrics at a glance. Such capabilities not only promote efficient resource management but also facilitate preventive maintenance, helping to prolong the machine’s lifespan.

Safety is paramount in the design of the G-4.5R, with multiple safety mechanisms in place. These include automatic shutdown features in case of system overloads, reinforced caging to protect operators, and enhanced visibility systems that ensure a clear line of sight during operation.

In summary, the Stow G-4.5R is a versatile, powerful, and user-friendly machine specifically designed for challenging work environments. With its combination of advanced technologies, ergonomic design, and safety features, the G-4.5R stands out as a top choice for professionals aiming for efficiency and reliability in their operations.
Top Page Image Contents