Troubleshooting

continued from previous page

Poor Water Flow:

1.Clean filter

2.Check if adjustable jets (are all open)

3.May have air lock, prime pump by loosening top pump union.

4.If water diverted valves are present make sure they are all the way open.

5.If gate valves are present, make sure they are all the way open.

6.If none of this works possible line obstruction or impeller loose on pump drive shaft

No water or air flow to jet:

1.If adjustable jets, probably in off position. (At times can lock into position, may require some effort.)

2.Pinched line, cutting off flow before reaching spa.

3.Water diverter valve if present may be closed.

Air controls not working:

1.Remove cap on air valve, (with flat head screw driver) and make sure not broken or improper alignment.

2.If internals are broke, call tech support

Jets Only Have One Speed:

1.Check pump connection at pack make sure power off (red plug.)

2.Programming error, call Tech Support.

3.Button not working properly, call Tech Support

Light Not Working:

1.Check for proper connection on pack and in line at red alligator clips.

2.Check for proper connection at light.

3.Call Tech Support

Heat not working: (No blinking decimal in lower right corner of control display)

1.Check desired temperature is higher than current temperature.

2.Make sure Jets are on low speed

3.Aux must also be turned off.

Heat not working: (Blinking decimal, but no heat)

1.Give spa time to heat up and be sure to cover.

2.Bad heater, call tech support

Water temperature not close to displayed temperature:

1.Check thermister is located in thermalwell and insulated by rubber gasket.

2.Make sure that air vents are unobstructed.

LOC

1. Press Heat and Jets key simultaneously. This will activate and deactivate this code.

Display flashes “FLO” (FLOW)

1.This indicates that there is a water flow problem or defective pressure switch.

2.Make sure filters are clean

3.Check that service valves are open

4.Check for obstruction of flow

5.Adjust pressure switch (see pressure switch detail under description and use of controls)

Freeze Protect Over-ride FPO

This function is intended to be used on start-up after a fresh fill if water temp is below 52ºF. The 6 hour duration of the FPO cycle is counted from the time the unit is powered-up and not from the time of its activation.

By pressing the Jets 1 and Light key simultaneously for 10 seconds, the freeze protect feature will be suspended for 6 hours. ( the FPO will be activated) This is to allow the installer of the spa to check for normal operation if the spa is filled with water that is less than the set freeze protect level 52ºF. FPO will appear every 10 seconds at the topside control. To manually go back to freeze protect mode, power down the system and re-boot. It is recommended that the system be left on low speed and heating in FPO mode.

8

Page 9 Page 11
Page 10
Image 10
Strong Pools and Spas Strong Spas The Antigua owner manual Loc
Page 9 Page 11

Strong Spas The Antigua specifications

Strong Pools and Spas is renowned for its innovative approach to creating high-quality hot tubs and spas, and their Strong Spas line, particularly the Antigua model, exemplifies this commitment to excellence. The Antigua offers a perfect blend of luxury, comfort, and cutting-edge technology, making it an exceptional choice for those looking to enhance their relaxation experience.

At the heart of the Antigua is its ergonomic design, which ensures that users can unwind in ultimate comfort. Featuring a spacious interior that accommodates up to five adults, the seating arrangement is optimized for a delightful hot tub experience. The thoughtfully positioned jets deliver a range of massage experiences, targeting various pressure points on the body, allowing for a rejuvenating soak that can relieve stress and tension.

One of the standout features of the Antigua is its advanced hydrotherapy system, which includes a combination of directional and spinning jets. These jets are adjustable, allowing users to customize their massage intensity, further personalizing their spa experience. The soothing hydrotherapy not only promotes relaxation but also aids in muscle recovery and enhances overall well-being.

The Antigua is constructed using a sturdy, rotationally molded shell that is not only durable but also designed to resist fading and cracking over time. This material ensures longevity while maintaining its aesthetic appeal. The spa is available in various colors, allowing owners to choose a style that complements their outdoor space.

Technology is a significant aspect of the Antigua, as it comes equipped with an intuitive digital control system. This allows users to adjust the temperature, jet settings, and lighting with ease. Additionally, the spa is designed with energy efficiency in mind, featuring an insulated cabinet and a high-performance heating system that helps to minimize energy costs while maintaining ideal water temperatures.

Safety is also a priority for Strong Pools and Spas, and the Antigua includes features such as a locking cover and non-slip surfaces. This ensures that families can enjoy their spa with peace of mind.

Overall, Strong Spas' Antigua represents an ideal combination of luxury, comfort, and innovative technology. Its exquisite design, superior hydrotherapy features, and user-friendly controls make it a top choice for those seeking a high-quality spa experience in their own backyard.
Top Page Image Contents