Sub-Zero Sub-Zero A N N I N G I N F O R M a T I O N, E C T R I C a L R E Q U I R E M E N T S

P L A N N I N G I N F O R M A T I O N

Although the Sub-Zero Built-In line offers a wide range of designs and configurations, the basic planning considerations for all models have much in common. As you integrate Built-In models into your overall plan, review installation requirements for your particular model(s). The Installation Specifications illustrations provide planning information for all Built-In models— overlay and stainless steel.

Allow the door(s) to open a minimum of 90˚ or you‘ll have problems removing drawers. With the door opening at 90˚, you may have to move drawers slightly to clear the door interior.

For corner installations, allow for a minimum 76 mm filler so that the door can open to 90˚. If you‘re using raised panels, consider using a wider filler.

When units are installed side by side, a filler strip is recommended. The width of this filler strip will vary depending on the configuration and panels you use.

Be sure to add the filler strip width to your finished rough opening dimension. In any installation of two units side by side without a filler strip, add an additional 13 mm to your combined numbers. This will allow for the proper width.

IMPORTANT NOTE: Refer to the full-scale illus- trations at the end of this section for specifics on door openings and filler size alternatives.

E L E C T R I C A L R E Q U I R E M E N T S

International models from the factory designed without a transformer require a 220/240 V AC, 50/60 Hz electrical supply, fused at the correct rating for the unit. If required by local or national codes, the power cord can be easily replaced using the power inlet device.

International models using a factory installed transformer require a 220/240 V AC, 50/60 Hz electrical supply, fused at the correct rating for the unit. These models will come equipped with Schuko power cords. The power cord may need to be replaced depending on local and national codes. The USA power cord that is supplied with the product must be disconnected with the appropriate transformer output to be connected in its place.

IMPORTANT NOTE: The electrical outlet must be grounded. The outlet must be flush with the back wall. Refer to the Installation Specifications illustration for your model for exact placement.

IMPORTANT NOTE: A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation.

P L U M B I N G C O N S I D E R A T I O N S

For Built-In models with an automatic ice maker, rough in the water supply line. Connect a

6.35mm OD copper line to the house supply, being sure to use an easily accessible shut-off valve between the supply and the refrigerator.

Do not use self-piercing valves. A saddle valve kit (4200880) is available from your Sub-Zero dealer.

For Built-In models, a line filter is required when water conditions have a high sediment content. The ice maker operates on water pressure of 1.4 bar to 6.9 bar.

IMPORTANT NOTE: In some cases a reverse osmosis water filter system may not be able to maintain the minimum water pressure consistently.

IMPORTANT NOTE: A reverse osmosis system can be used with Models ICB648PRO and ICB648PROG, provided there is constant water pressure of 1.4 bar to 8.3 bar supplied to the unit at all times.

The water line should be routed up through the floor within 13 mm from the back wall and no higher than 76 mm off the floor. If you have to come through the wall, make sure the water line is no more than 76 mm from the floor.

Regardless of the routing, allow 1 m of excess copper tubing to remain outside the wall or floor for easy connection to the unit. Refer to Installa- tion Specification illustrations.

M O D E L O P T I O N S

Model I601R

914 mm

All Refrigerator

Model I601RG

914 mm

All Refrigerator with Glass Door

Model I601F

914mm

All Freezer

Model I611

762 mm Over-and-Under

Model I611G

762 mm Over-and-Under with Glass Door

Model I650

914 mm Over-and-Under

Model I650G

914 mm Over-and-Under with Glass Door

Model I661

914mm

Side-by-Side

Model I642

1067 mm Side-by-Side

Model I685

1067 mm Side-by-Side

Ice Water Dispensing

Model I632

1219 mm Side-by-Side

Model I695

1219 mm Side-by-Side

Ice Water Dispensing

Model ICB648PRO

1219 mm Side-by-Side

Built-In or Free-Standing

Model ICB648PROG

1219 mm Side-by-Side with Glass Door

Built-In or Free-Standing

13