Sunrise Medical P-222 Remote Joystick SWING-AWAY Retractable, Mount Optional, Seat Depth

32	I X . S e t - U p , A d j u s t m e n t & U s e
H. REMOTE JOYSTICK SWING-AWAY RETRACTABLE
MOUNT (OPTIONAL)
The remote joystick is mounted with a mechanism
which allows the control to be locked in a forward or
retracted position.
Adjustment	E
a. To retract joystick, depress lever (E) located on
side of armrest.
b. Push joystick away from front of armrest until it

I X . S e t - U p , A d j u s t m e n t & U s e			33
2.	Height Adjustment		4
	a. Rotate release lever to stop.
		5	3
	b. Slide armrest pad up or down to desired
	height.		1
	c. Return lever to locked position.
			7
	d. Push arm pad until upper armpost locks firmly
		2	8
	into place.
3.	Removing Armrest		6
	a. Rotate release lever and remove the armrest.		9
4.	Replacing Armrest	Height-Adjustable Armrest Key

locks into retracted position.

c. To return to forward position, depress lever and

push joystick forward until it locks into place.

a. Slide armrest back into receiver. b. Return release lever to locked

position against armpost.

1.	Inner Arm Post
2.	Receiver
3. Release Lever, Locked Position

I. DUAL-POST HEIGHT-ADJUSTABLE ARMRESTS

The dual-post flip-back armrest can be used as either a flip-back armrest or a removable armrest.

1.	Installing Armrest
	a. Insert front and rear posts into armrest receivers.
	b. Tighten clamp levers (A) and (B) to secure armrest.
2.	Set-up for Flip-back Operation
	a. Loosen clamp lever (A) so front post is able to

C

B

A

5. Adjusting Armrest Receiver Fit

To tighten or loosen the fit of the outer armpost in the receiver:

a. Loosen the four bolts on the sides of the receiver.

b. With the armrest in the receiver, squeeze the receiver to achieve the desired fit.

c. Tighten the four bolts.

6. Adjusting Inner Armpost Fit

4.	Armrest Pad
5.	Transfer Bar
6.	Side Panel
7. Tension Adjustment Set Screw
8.	Outer Arm Post
9.	Receiver Adjustment Bolts

come free.

b. Armrest now has the ability to be flipped back

without removal.

3. Set-up for Removal

a. Two set screws are installed in the outer arm- post.

b. Turn the set screws in or out until the desired fit is achieved.

a. Insert front and rear posts into armrest receivers b. Loosen clamp lever (A) and (B) so front and rear

post are able to come free.

c. Armrest can now be easily removed for transferring.

4.Height-Adjustment (option)

a.Release the upper securing lever (C).

b.Set at desired height

c.Return securing lever to locked position.

d.Move armrest up or down to allow armrest to snap into place

J.SINGLE POST HEIGHT-ADJUSTABLE ARMRESTS (OPTIONAL)

1.Installation

a.Slide the outer armpost into the receiver mount- ed to the wheel chair frame.

b.The armrest will automatically lock into place.

K. SEAT DEPTH

The seat depth can be adjusted in one inch increments.
1. Seat Frame Depth Adjustment
a. To adjust, remove the two bolts (C & D) from
each side of the backrest pivot plate.	D
b. Reposition the backrest to the desired position.
	C
c. Replace and retighten bolts on each side of
the backrest pivot plate.

930466 Rev. A 930466 Rev. A