12
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
REFERENCE
Firebox Accessories / Parts
Cat. No. Model No. Description
88L53 FGE Bag of Glowing Embers
80L42 FDVS Bag of Decorative
Volcanic Stone
Glowing Embers
Bag of Glowing
Embers (rockwool)
Separate into Quarter
Size (separate) Pieces
INSTALL VOLCANIC STONE, GLOWING
EMBERS AND LOGS
1. Remove the front glass enclosure panel
(see Removing Glass Enclosure Panels on
Page 11).
2. Carefully remove the log set box from
the firebox. Next, remove embers and
volcanic stone from the control compart-
ment. Handle logs carefully to prevent
breakage.
3. Install Decorative Volcanic Stone - Mound
up a portion of the volcanic stone in front
of the burner in a pleasing pattern.
4. Placement of Glowing Embers -
Separate the Embers (rockwool) into pieces
about the size of a quarter (see Figure 6).
Keep the pieces fluffed up, not matted.
Distribute these pieces over the surface of
the burner, as shown in Figure 7 on Page
13. Do not use more than is necessary.
Ensure that the main burner slots remain
uncovered by the ember material.
Note: This appliance is provided with enough
Glowing Embers for several applications, do
not use all that is in a new bag at one time.
For best glowing effect, replace the ember
material annually.
5. Placement of Logs -
The logs have locating notches or slots to
help ensure that they are properly posi-
tioned. Proper log placement is critical to
prevent sooting.
INSTALLATION PROCEDURE
Carefully position the ceramic fiber logs into
the firebox as shown in Figure 7 on Page 13.
Logs should be placed in the order shown and
per the following instructions.
Figure 6
1. Place embers on the front burner tube and
volcanic stone in front of the burner as
shown and per instructions on Page 13 (see
Placement of Glowing Embers and Install
Decorative Volcanic Stone on this Page).
2. Place the rear log (A) as shown. Position
the 2 notches on the bottom of log (A) over
the 2 corresponding locating brackets as
shown.
3. Place the center log (C) as shown. The 2
notches on the bottom of log (C) fit over
the corresponding locating brackets.
4. Place the left log (B) as shown. The top fork
on log (B) fits into the notch on log (A). The
bottom of log (B) rests on the sub-floor.
5. Place the top right log (D) as shown. The top
fork on log (D) fits into notch on log (A) as
shown. The bottom fork on log (D) rests on
sub-floor flange (identified in photo #1).
WARNINGS•
DO NOT attempt to install the
logs until the appliance instal-
lation has been completed, the
gas line connected and tested
for leaks and the initial burner
operation has been checked
out.
•
The size and position of the log
set was engineered to give the
appliance a safe, reliable and
attractive flame pattern. Any
attempt to use a different log
set in the fireplace will void
the warranty and will result in
incomplete combustion, soot-
ing, and poor flame quality.
•
Logs get very hot and will
remain hot up to one hour
after gas supply is turned
off. Handle only when logs
are cool. Turn off all electric-
ity to the appliance before
you install volcanic stone,
embers and logs.
•
This appliance is not designed
to burn wood. Any attempt to
do so could cause irreparable
damage to appliance and prove
hazardous to your safety.
•
If logs are not installed accord-
ing to the log in stallation
instructions, flame impinge-
ment and improper combus-
tion could occur and result in
soot and/or excessive produc-
tion of carbon monoxide (CO),
a colorless, odorless, toxic
gas.