|
|
|
|
| If you need additional operating assis- |
OWNER’S MANUAL | tance after reading this owner’s manual | ||||
or to order replacement accessories, | |||||
VIDEO CASSETTE RECORDER | please call | ||||
C6240VE |
|
|
|
| TOLL FREE : |
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
1. Before using your VCR
RF Output Channel
If channel 3 is already occupied for broadcasting,1)Set your TV to channel 4.
2)Insert a
3)Press the PLAY button once.
4)After a few seconds, press the PLAY button on the VCR for 3 seconds.
•The RF output channel will change to channel 4 from channel 3 and you will see a playback picture.
•When a picture does not appear on the TV screen, repeat step [4].
5) Press the STOP button to stop playback.
HintHint
•The RF output channel may not change when you adjust tracking during playback. In this case, stop the playback, and start the playback again. After that, press the PLAY but- ton on the VCR for 3 seconds again.
Basic VCR/TV Connection
Stereo TV Connection
Cable Antenna
Signal
or
(Back of TV) |
Disconnect |
Cable Antenna
Signal
or
2 |
Connect
(Back of VCR)
(Back of TV)
ANT |
|
IN | 3 |
OUT | |
| Connect |
You can use the AUDIO OUT jack and VIDEO OUT jack on the back of the VCR if your TV has Audio/Video Input jacks. In this case, you need to set the TV to external Line Input Mode. Please refer to your TV’s owner’s manual.
VIDEO AUDIO IN |
| ||
IN | L | R | ANT |
|
|
| IN |
AUDIO |
| |
OUT | IN | OUT |
VIDEO |
| |
Audio/Video Cables |
|
|
(not supplied) |
|
|
1 |
|
|
| Connect |
(Back of TV) | (Back of VCR) |
|
RF Cable (supplied)
4 Plug the AC power cords of the VCR and TV into the AC outlets.Hint for Cable Box or Satellite Box
Front & Rear Terminals
AUDIO OUT jackConnect the audio cable to the audio in jack of a camcorder, another VCR, a stereo amplifier, or an audio system.
Connect the audio cable from the audio out jack of a camcorder, another VCR, or an audio source.
Connection A | (Back of VCR) |
(Cable | box or | ANT | |
Satellite box) | |||
IN |
Connection B |
| (Back of VCR) | |
| ANT | (Cable | box or |
| IN | ||
|
|
ANT
ANT | ANT IN jack |
IN | |
| Connect your antenna or cable box. |
IN | OUT | OUT | RF Cable | E |
Cable |
| |||
|
|
| ||
|
| (supplied) |
| |
Signal |
|
|
| |
|
|
| (Back of TV) | |
|
|
|
|
Select this connection when you want to view or record a
Cable | Satellite box) | |
OUT | E | |
Signal | IN | OUT |
|
| |
| RF Cable (supplied) | RF Cable (Back of TV) |
Select this connection when you want to change channels
AUDIO
OUT IN
VIDEO
VIDEO OUT jackIN
OUT
AUDIO
OUT IN
VIDEO
| ANT OUT jack |
OUT | Connect the RF cable (supplied) to |
| |
| the antenna input jack on your TV. |
scrambled channel.
• With this connection, channels cannot be changed on the |
VCR. You can view or record ONLY the channels you have |
on the VCR. With this connection, you may watch one channel while recording another.
• You may not view or record a scrambled channel.
Connect the video cable to the video in jack of a camcorder, another VCR, or a TV.
Connect the video cable from the video out jack of a camcorder, another VCR, or an
selected on the cable box or the satellite box. |
• While you are recording, only the recorded channel can |
be viewed. |
To select channels of the cable box or satellite box
1)Turn on the VCR by pressing the POWER button, and then, press the VCR/TV button.The POWER and the VCR/TV indicators on the front panel will light on. Then, press the CHANNEL buttons to select channel 3 or 4 (the same channel as the output channel of the cable box or satellite box).
•If you use the channel 4, you need to change the VCR’s RF output to channel 4. Refer to “RF Output Channel”.
2)At the TV, select channel 3 or 4 (the same channel as you have selected at step 1).
3)At the cable box or satellite box, select the channel you
want to view or record.
|
|
| POWER CHANNEL |
| |
To select channels of the cable box or satellite box |
| VIDEO | n | m |
|
| AUDIO | POWER VCR/TV TAPE IN TIMER R | |||
1)At the cable box or satellite box, select channel 3 or 4 |
|
|
|
|
|
(the same channel as the VCR’s RF output channel.) |
|
|
|
|
|
• Refer to “RF Output Channel”. |
|
|
|
|
|
2)At the TV, select the same channel as the output chan- |
| Supplied Accessory |
| ||
nel (3 or 4) of the cable box or satellite box. |
|
| |||
3)Turn on the VCR by pressing the POWER button, and |
| • Remote control | • RF Cable | • Owner’s Manual | |
then, press the VCR/TV button .The POWER and |
| ||||
VCR/TV indicators on the front panel will light on. Then, | (NA371UD) with | (WPZ0901TM002) | (0VMN04007) | ||
select the channel you want to view or record. |
| Two AA batteries |
|
| |
To play back a tape |
|
|
|
|
|
Follow the steps 1) to 2) above. Then, play back a tape. |
|
|
|
|
|
• Refer to “Playback” on page 5. |
|
|
|
|
|
To view one channel while recording another |
|
|
|
|
|
1)While you are recording on the VCR, press the VCR/TV but- |
|
|
|
| |
ton so that the VCR/TV indicator disappears on the VCR. |
|
|
|
|
|
2)At the cable box or satellite box, select the channel you |
|
|
|
| |
want to view. | - 1 - |
|
|
| |
|
|
|
|
Installing the Batteries for the Remote Control
Install two AA batteries (supplied) matching the polarity indicated on the bottom of the remote control.
Printed in China
0VMN04007 / HF350CD ★★★★★