Sylvania DVC865G

– 27 –

1Turn on the TV and set it to channel 3.

• If channel 3 has been already occupied for broadcasting,

see “RF Output Channel” section.

2Select your language in the first time you turn on this unit.

Then press [B] to go to next step.

POWER

Quick Use Guide

Please refer to “Basic TV Connection” on the front page

before you use this unit.

RF Output Channel

If channel 3 has been already occupied for broadcasting,

1) Set your TV to channel 4.

2) Insert a pre-recorded tape into this unit.

3) Press [OUTPUT] on the unit so that the VCR OUTPUT

light is lit.

•

If noise appears on the TV screen, press [VCR/TV] on the

remote control.

4) Press [PLAY B] once.

5) After a few seconds, press and hold [PLAY B] on the

unit for 3 seconds.

• The RF output channel will change to channel 4 from

channel 3 and you will see a playback picture.

• When a picture does not appear on the TV screen,

repeat step 4.

6) Press [STOP C] to stop playback.

1Connections

Clock Set Up

Turn On the Unit for the First Time

VCR/DVD Switching

Installing the Batteries for the Remote

Control

CHANNEL

OPEN/CLOSE

VCR DVD

PROGRESSIVE SCAN

SKIPHSTOP PLAY G SKIP

REV FWD

OUTPUT

DVDVCR

OUTPUT button

DVD OUTPUT

light

VCR OUTPUT light

DVD button

VCR button

POWER

DISPLAY VCR DVD PAUSE

SLOW

VCR/TV

SKIP/CH.

PLAY

STOP

REC/OTR

SETUP TOP MENU

MODE ZOOM

SUBTITLE

T-S ET

ANGLE

ENTER

RETURN

MODE

REPEAT A-B

OPEN/CLOSE

/EJECT

SPEED AUDIO

CLEAR/

C. RESET

123

456

789

+10

VCR MODE

Press [VCR] on the remote control.(Verify that the VCR OUTPUT

light is lit.)

DVD MODE

Press [DVD] on the remote control.(Verify that the DVD OUTPUT

light is lit.)

Please wait for a few minutes.

After scanning...

• The tuner stops on the lowest memorized channel.

• You can select only the channels memorized in this unit by using

[SKIP/CH. G/K, H/L] (or [CHANNEL K/L]).

• If “AUTO SET UP” appears on the TV screen again, check the cable

connections. Then, press [B] once again.

Yes

Press [MENU] to exit.

Do you connect the cable from the cable box or the satellite box to the unit’s

ANT-IN jack?

Hint

• Pressing only [OUTPUT] on the front panel DOES NOT switch the

mode of the remote control. You MUST select the correct mode on

the remote control.

1Press [MENU] and select “CLOCK SET“.

Then press [B] to go to next step.

2Select the current month.

Then press [B] to go to next step.

3Select the current day.

Then press [B] to go to next step.

4Select the current year.

Then press [B] to go to next step.

5Select the current hour.

Then press [B] to go to next step.

6Select the current minute.

Then press [B] to go to next step.

7Select “AM” or “PM”.

8To exit the CLOCK SET screen

• If the clock is not set, the CLOCK SET screen appears when you press

[MENU]. In this case, go to step 2.

- M E N U -

TIMER PROGRAMMING

AUTO REPEAT [OFF]

CHANNEL SET UP

B CLOCK SET

LANGUAGE SELECT

AUDIO OUT

TV STEREO [ON]

SAP

CLOCK SET

MONTH DAY YEAR

1 0 / – – – – – –

HOUR MINUTE AM/PM

– – : – – – –

CLOCK SET

MONTH DAY YEAR

1 0 / 0 2 – – – –

HOUR MINUTE AM/PM

– – : – – – –

CLOCK SET

MONTH DAY YEAR

1 0 / 0 2 2 0 0 6

HOUR MINUTE AM/PM

– – : – – – –

CLOCK SET

MONTH DAY YEAR

1 0 / 0 2 MON 2 0 0 6

HOUR MINUTE AM/PM

0 5 : – – – –

CLOCK SET

MONTH DAY YEAR

1 0 / 0 2 MON 2 0 0 6

HOUR MINUTE AM/PM

0 5 : 4 0 – –

CLOCK SET

MONTH DAY YEAR

1 0 / 0 2 MON 2 0 0 6

HOUR MINUTE AM/PM

0 5 : 4 0 P M AM

B PM

LANGUAGE SELECT

B ENGLISH [ON]

FRANCAIS

ESPAÑOL

3Press [B] to start Auto Set Up. CH 01

AUTO SET UP

YES

VCR

✄

E8A00UD_E8C00UD.indd 27E8A00UD_E8C00UD.indd 27 2006/08/18 13:11:412006/08/18 13:11:41