Setup
– 8 –EN
1Turn on the TV and set it to channel 3.
• If channel 3 has been already occupied for broadcasting,
see “RF Output Channel” section on page 6.
2Select your language in the first time you turn on this unit.
Then press [B] to go to next step
.
3Press [B] to start Auto Set Up.
or
POWER
1Press [MENU] to select “CHANNEL SET UP”.
Then press [B] to go to next step.
2Select “MANUAL SET UP”.
Then press [B] to go to next step.
3Select the channel to be added or deleted.
4Select “ADD” or “DELETE”.
5To exit the menu
1Press [MENU] and select “CLOCK SET”.
Then press [B] to go to next step.
2Select the current month.
Then press [B] to go to next step.
3Select the current day.
Then press [B] to go to next step.
4Select the current year.
Then press [B] to go to next step.
5Select the current hour.
Then press [B] to go to next step.
6Select the current minute.
Then press [B] to go to next step.
7Select “AM” or “PM”.
8To exit the CLOCK SET screen
To Preset the Channel Again
1) Press [MENU] until the main menu appears.
2)
Select “CHANNEL SET UP” by using
[K//L]
, then press
[B]
.
3)
Select “AUTO SET UP” by using [K//L], then press [B]. After
scanning, the tuner stops on the lowest memorized channel.
To Change the On-Screen Language
1)
Press
[MENU]
until the main menu appears.
2) Select “LANGUAGE SELECT” by using [K/L], then
press [B].
3) Select “ENGLISH” , “FRANCAIS” or “ESPAÑOL” by
using [K/L] then press [CLEAR/C.RESET].
To Select a Channel
You can select a channel by using the Number buttons or
[
SKIP/CH.
G
/
K
,
H
/
L].
Notes for using the Number buttons:
• When selecting cable channels which are higher than 99,
enter channel numbers as a three-digit number. (for exam-
ple: 117, press [1], [1], [7])
• You must precede single-digit channel numbers with a zero.
(for example: 02, 03, 04 and so on)
• If the clock is not set, the CLOCK SET screen appears when you press
[MENU]. In this case, go to step 2.
To Add or Delete Channels
CLEAR/
C. RESET
Preparation for Use
Hint
• Repeat these steps only if either there was a power failure or this unit has been
unplugged for more than 30 seconds.
No
Please wait for a few minutes.
After scanning...
• The tuner stops on the lowest memorized channel.
• You can select only the channels memorized in this unit by using
[SKIP/CH. G///K, H//L] (or [CHANNEL K///L]).
• If “AUTO SET UP” appears on the TV screen again, check the cable
connections. Then, press [B] once again.
Yes Press [MENU] to exit.
• Refer to “Hint for Cable Box or Satellite Box” section on page 6.
Do you connect the cable from the cable box or the satellite box to the unit’s
ANT-IN jack?
Hint
• To go back one step, press [s] (during steps 2 to 7).
• Your clock setting will be lost if either there is a power failure or this unit has
been unplugged for more than 30 seconds.
or
or
MENU
or
or
or
or
or
or
MENU
or
• If the clock is not set, the “CLOCK SET” screen appears when you press
[MENU]. In this case, press [MENU] again.
LANGUAGE SELECT
B ENGLISH [ON]
FRANCAIS
ESPAÑOL
CH 01
AUTO SET UP
- M E N U -
TIMER PROGRAMMING
AUTO REPEAT [OFF]
B CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO [ON]
SAP
CHANNEL SET UP
AUTO SET UP
B MANUAL SET UP
MANUAL SET UP
CHANNEL 30 (CATV)
ADD
MANUAL SET UP
CHANNEL 30 (CATV)
DELETE
- M E N U -
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
B CLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO [ON]
SAP
CLOCK SET
MONTH DAY YEAR
1 0 / – – – – – –
HOUR MINUTE AM/PM
– – : – – – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 2 – – – –
HOUR MINUTE AM/PM
– – : – – – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 2 2 0 0 6
HOUR MINUTE AM/PM
– – : – – – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 2 MON 2 0 0 6
HOUR MINUTE AM/PM
0 5 : – – – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 2 MON 2 0 0 6
HOUR MINUTE AM/PM
0 5 : 4 0 – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 2 MON 2 0 0 6
HOUR MINUTE AM/PM
0 5 : 4 0 P M AM
B PM
or
or or
or
NO
YES
Turn On the Unit for the First Time
VCR
VCR
Clock Setup
VCR
VCR
Operation described in this manual are
mainly based on the remote control.
Hint
• If you accidentally select Spanish or French and need English: Press [MENU]
and choose SELEC. IDIOMA or SELECTION LANGUE. Press [B] and select
ENGLISH. Finally, press [CLEAR/C.RESET].
• To add or delete channels in this unit, [SKIP/CH. G//K, H/L] button works
on the channel number memorized in this unit, [K/L] works on all.
E8A00UD_E8C00UD.indd 8E8A00UD_E8C00UD.indd 8 2006/08/18 13:11:042006/08/18 13:11:04