Sylvania LD190552 Initial Setup, Before you begin, After an initial setup is completed

These operations are accessible by remote control.

Some may also be accessible by controls on the main unit.

Initial Setup

This section will guide you through the unit’s initial setting which includes selecting a language for your on-screen menu and autoprogram, which automatically scans and memorizes viewable channels.

Before you begin:

Make sure the unit is connected to antenna or cable.

1 After making all the necessary connections, press POWER to turn on the unit.

•It may take a few moments to turn on the unit for the first time.

•[Initial Setup] menu appears automatically after the unit is turned on.

2 Use ▲/▼ to select the on-screen language from the choices (English / Español / Français) on the right side of the TV screen, then press ENTER.

3 Use ▲/▼ to select [Antenna] for TV channels or [Cable] for CATV channels, then press ENTER.

Initial Setup

Make sure the antenna is connected to ''ANT. IN'' jack.			Antenna
			Cable
Select your signal source.
			Skip
Antenna
Cable	Or	ANT.IN
Select	ENTER Enter	Back	Skip

•[Autoprogram] will begin.

Initial Setup

Please wait while the system is scanning for channels. Auto programming may take more than 20 minutes to complete.

0%

Digital channels	0 ch
Analog channels	0 ch

Skip

		English	13
4 Use ◄/► to select the desired location setting, then press			INTRODUCTION
ENTER.
	Initial Setup

Select “Retail” or “Home” for your location.

Select	ENTER Enter	PREPARATION
Retail	Home

	• Select [Retail] store, the unit will be set up with
		predefined setting for retail displays. In this setting, the				WATCHING
		power consumption may possibly exceed the limited
		requirement of the ENERGY STAR® qualification.
	• Select [Home], the unit is set to maximize the energy
		efficiency for home setting and it can be adjusted
						TV
		through a choice of picture and sound quality according
		to your preference.
	• When the initial setup is completed, the lowest
						USING
		memorized channel with the confirmation message of
		the location setting will be displayed on the TV screen.
						FUNCTIONS
Note
• If you are not receiving a signal from your cable service, contact
	the Cable provider.
• If you press POWER or SETUP during autoprogram, this setting
	will be canceled.
•	The initial autoprogram function can be executed for either					OPERATING
	[Antenna] or [Cable] only once. When you change the
•	connection (Antenna / Cable), set [Autoprogram] again. ➠ p.19
	If there is no signal input from the antenna terminal and no
	operation for several seconds after you turn on the unit, helpful
						DVD
	hints appears. Follow the instructions listed on the TV screen.
		Initial Setup
					Retry	CONNECTING
		No channel is registered.			Later
		Try Autoprogram again?
		Verify that you have a cable connected to the “ANT. IN” jack
		on the back of the TV, the channel installation process
		searches this connection. If you are using a cable or satellite
		box, please confirm the input which you have connected to the				DEVICES
		box and press “INPUT SELECT” key on the remote control to
		select the appropriate source input.
		Select	ENTER Enter	Skip
						USEFUL
• You must set [Home] in step 4. Otherwise, [Picture] and [Sound]
	settings you adjusted will not be memorized after the unit goes
	into standby mode.
						TIPS
After an initial setup is completed
	• If you want to scan the channels automatically again.
		[Autoprogram] ➠ p.19				INFORMATION
	• You can add the desired cable and analog channels
		unmemorized by autoprogram.
		[Add Channels] ➠ p.20
	• If you want to change to another language.
		[Language] ➠ p.25
	• If you want to change the location setting.
		[Location] ➠ p.24