The channels you no longer receive or seldom watch
can be deleted from the memory. (Of course, you
can add the deleted channel into the memory again.)
1Select “CHANNEL SET UP”
Press the MENU button on the
remote control.
Press the PLAY/Kor STOP/Lbut-
ton to point to “CHANNELSET
UP”.
Then press the F.FWD/Bbutton.
2Select “ADD/DELETE CH”
Press the PLAY/Kor STOP/Lbut-
ton to point to “ADD/DELETE
CH”.
Press the F.FWD/Bbutton.
3Enter the desired channel number
Press the PLAY/Kor STOP/Lbut-
ton until your desired channel num-
ber appears. (You can also use the
number buttons or the CHANNEL
K/Lbutton to enter it) (Example:
CH8)
•You must precede single-digit channel numbers
with a zero (Example: 02 ... 09).
•When selecting cable channels which are higher
than 99, press the +100 button first, then press the
last two digits. (Example: to select channel 125,
first press the +100 button then press “2” and “5”).
4Delete (or add) it from (into) memory
Press the F.FWD/Bor REW/sbutton. The channel
number changes to light red. The channel is deleted
from memory.
•To delete another channel, repeat steps [3] and [4].
•If you press the F.FWD/Bor REW/sbutton
again, the channel is memorized again.
5Exit the channel setup mode
Press the MENU button on the remote control to
return to TVmode.
NOTE: To confirm that channel(s) has been deleted
or added, press the CHANNELKor Lbutton.
- 13 - EN
9I03
DELETING (OR ADDING)CHANNEL(S)
Added channel:Light blue .
Deleted channel: Light red.
CHANNEL SET UP
Make sure ...
•Press the POWER button to turn on the TV/VCR.
1Select “CHANNEL SET UP”
Press the MENU button on the
remote control.
Press the PLAY/Kor STOP/Lbut-
ton to point to “CHANNELSET
UP”.
Then press the F.FWD/Bbutton.
2Begin auto preset
Press the PLAY/Kor STOP/Lbut-
ton to point to “AUTO CH PRO-
GRAMMING”.
Then press the F.FWD/Bbutton.
The tuner scans and memorizes all
the active channels in your area.
3After scanning
The tuner stops on the lowest memorized channel.
•When AUTO CH PROGRAMMING is activated
where there is no TVsignal input, “NO TV SIG-
NALS” will appear on the display after the com-
pletion of the channel scanning.
•The TV/VCR may recognize TVchannels to be
CATVchannels by the receiving conditions. In this
case, try auto preset again in the fine receiving
conditions.
– M E N U –
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
BCHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
– CHANNEL SET UP –
BADD / DELETE CH (CATV)
AUTO CH PROGRAMMING
08
ADD / DELETE
– M E N U –
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
BCHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
– CHANNEL SET UP –
ADD / DELETE CH (CATV)
BAUTO CH PROGRAMMING
You can program the tuner to scan all the channels
you receive in your area.
NOTE: Channel setup is NOT needed when connect-
ed to a cable box or satellite box. Just select the
TV/VCR channel selector to the output channel of
the cable box or satellite box (Ex CH3), then select
the channel to be viewed on the Cable Box or
Satellite Box.