Sylvania SRDD495 Preparation for Use, Turn On the Unit for First Time, To Add/Delete Channels

Preparation for Use

Turn On the Unit for the

First Time

VCR

VCR

1

Turn on the TV and set it to channel 3.

•If channel 3 is already occupied for broadcasting, see“RF Output Channel” section.

2	POWER	Remote Control	TV Screen
		LANGUAGE SELECT
		B ENGLISH	[ON]
Setup		FRANCAIS
		ESPAÑOL
	or

To Add/Delete Channels

1	MENU	- M E N U -
		TIMER PROGRAMMING
		AUTO REPEAT [OFF]
		B CHANNEL SET UP
		CLOCK SET
		LANGUAGE SELECT
		• If the clock is not set, the
	or	“CLOCK SET” screen
		appears when you press
		[MENU]. In this case,
		press [MENU] again.
2		CHANNEL SET UP
		AUTO SET UP

B MANUAL SET UP

or

Hint

•If you accidentally select Spanish or French and need English: Press [MENU] and choose SELEC. IDIOMA or SELECTION LANGUE. Press [B] and select ENGLISH. Finally, press [CLEAR/C.RESET].

Clock Setup

VCR

VCR

1	MENU	- M E N U -
		TIMER PROGRAMMING
		AUTO REPEAT [OFF]
		CHANNEL SET UP
		B CLOCK SET
		LANGUAGE SELECT
		• If the clock is not set, the
	or	CLOCK SET screen
		appears when you press

[MENU]. In this case, go to step 2).

3	CH 01
	AUTO SET UP

3MANUAL SET UP

CHANNEL 30 (CATV)

ADD

or

Select the channel to be added or deleted.

2		CLOCK SET
	MONTH DAY		YEAR
	1 0	/ – –	– – – –
or	HOUR MINUTE		AM/PM
	– –	: – –	– –

Select the current month.

Do you connect the cable from the cable box or the satellite box to the unit’s ANT-IN jack?

YES

Yes Press [MENU]

to exit.

• Refer to “Hint for Cable Box or Satellite Box” section on page 6. NO

No Please wait for a few minutes.

After scanning...

•The tuner stops on the lowest memorized channel.

•You can select only the channels memorized in this unit by using [SKIP/CH. G/K H/L] (or [CHANNEL K/L]).

•If "AUTO SET UP" appears on the TV screen again, check the cable connections. Then, press [B] once again.

4	MANUAL SET UP
	CHANNEL 30	(CATV)
	DELETE
	or
	Select “ADD” or “DELETE”.

5 To exit the	CLEAR/
menu	C. RESET

3		CLOCK SET
	MONTH DAY		YEAR
	1 0	/ 0 3	– – – –
or	HOUR MINUTE		AM/PM
	– –	: – –	– –

Select the current day.

4		CLOCK SET
	MONTH DAY		YEAR
	1 0	/ 0 3	2 0 0 5
or	HOUR MINUTE		AM/PM
	– –	: – –	– –

Hint

•Repeat these steps only if either there was a power failure or this unit has been unplugged for more than 30 seconds.

To Select a Channel

You can select a channel by using the Number buttons or

[SKIP/CH. G/K H/L].

To Preset the Channel Again

1)Press [MENU] until the main menu appears.

2)Select “CHANNEL SET UP” by pressing [K/L], then press [B].

3)Select “AUTO SET UP” by pressing

[K/L], then press [B]. After scanning, the tuner stops on the lowest memorized channel.

Select the current year.

5	CLOCK SET
MONTH DAY		YEAR
1 0	/ 0 3 MON 2 0 0 5

Notes for using the Number buttons:

•When selecting cable channels which are higher than 99, enter channel numbers as a three-digit number. (For example: 117, press [1], [1], [7])

•You must precede single-digit channel numbers with a zero (for example: 02, 03, 04 and so on).

To Change the On-Screen Language

1)Press [MENU] until the main menu appears.

2)Select “LANGUAGE SELECT” by pressing [K/L], then press [B].

3)Select “ENGLISH” , “FRANCAIS” or “ESPAÑOL” by pressing [K/L] , then press

[CLEAR/C.RESET].

or	HOUR MINUTE	AM/PM
	0 5 : – –	– –

Select the current hour.

– 8 – EN