Sylvania SSD800 owner manual Hookups, DVD/VCR to TV Connection, Connecting to a TV

[Back of the DVD/VCR]

SETTING THE CH3/CH4

SWITCH

HOOKUPS

DVD/VCR TO TV CONNECTION

1.	Disconnect the AC power cord of the TV from the			If your TV does not have A/V terminals:
	AC outlet.			When the DVD/VCR COMBINATION UNITS is in
2.	Disconnect the antenna or cable from the TV.			the VCR Playback mode or when the DVD/VCR
3.	Connect the antenna or cable to the ANT-IN jack of			COMBINATION UNITS is in the VCR mode, your TV
	the DVD/VCR COMBINATION UNITS.			will receive signals from the DVD/VCR COMBINA-
4.	Connect the DVD/VCR COMBINATION UNITS to			TION UNITS on either channel 3 or channel 4. To use
	the TV using the RF cable.			the DVD/VCR COMBINATION UNITS with your TV,
5.	Plug the AC power cords of the DVD/VCR COM-			set the selector switch to CH3 or CH4 (which is locat-
	BINATION UNITS and TV into the AC outlets.			ed in the back of your
	[VHF/UHF	[Indoor antenna]	[Back of the DVD/VCR]	DVD/VCR COMBINATION
	combination antenna]		[Back of the	UNITS), whichever is not
			UHF/VHF combination TV]				ANT - IN
		OR	RF cable	used for normal broadcasts in	CH3	CH4
			ANT - IN	your area. Then set your TV			OUT
			(supplied) UHF/VHF
	[Cable	box or satellite box] OR					CH3 CH4
			ANT - OUT	to the same channel.
			CH3 CH4

From Cable or

Satellite Company

Note to CATV system installer

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that pro- vides guidelines for proper grounding and, in particular, specifies that the cable ground should be connected to the grounding system of the building, as close to the point of cable entry as practical.

CONNECTING TO A TV

			DVD/VCR	COMPONENT
			OUT
Antenna/Cable signal			IN	VIDEO OUT
		ANT - IN	L	DVD/VCR	Y
			AUDO	AUDIO OUT
					Cb S-VIDEO	DIGITAL AUDIO OUT
A/V-compatible or			R	L
					OUT	PCM / BITSTREAM
		ANT - OUT				COAXIAL
wide screen TV		CH3 CH4	VIDEO	R	Cr
	To ANT. IN
	of TV
	To VIDEO INPUT jack		To VIDEO OUT jack			[Fig. 1]
	To Right (red) and Left (white)
Notes	To AUDIO INPUT jacks		To AUDIO OUT jacks

¡Connect the DVD/VCR COMBINATION UNITS directly to a TV. If the A/V cables are connected to a VCR, pictures may be distorted due to the copy protection system.

CONNECTING TO A TV THAT HAS AN

S-VIDEO INPUT JACK OR COMPONENT VIDEO IN JACKS

FOR TVs WITH S-VIDEO INPUT JACK

Use an S-Video cable (commercially available) in place of the yellow video cable to enjoy higher quality pic- tures.

The S-Video connection only supplies video (picture) in the DVD mode of the DVD/VCR COMBINATION UNITS. Therefore, in order to use the VCR features or view TV channels on the DVD/VCR COMBINATION UNITS, you still need to either connect the RF cable to the ANT-OUT jack of the DVD/VCR COMBINATION UNITS and the TV’s Antenna In jack, or connect the yellow video cable as described earlier (Fig.1). To connect the supplied RF cable, see “DVD/VCR TO TV CONNECTION” above.

		DVD/VCR		COMPONENT
		OUT
		IN		VIDEO OUT
	ANT - IN	L		Y
			DVD/VCR
		AUDO	AUDIO OUT
A/V-compatible or					DIGITAL AUDIO OUT
		R	L	Cb S-VIDEO
				OUT PCM / BITSTREAM
wide screen TV	ANT - OUT				COAXIAL
	CH3 CH4	VIDEO	R	Cr
	To Right (red) and Left (white)
	To AUDIO INPUT jacks	To AUDIO OUT jacks			[Fig. 2]
	To S-VIDEO INPUT jack	To S-VIDEO OUT jack
		– 14 –			EN

1L25