Symbol Technologies LS 1000 , Maintaining the LS 1000 Scanner

3-2

LS 1000 Product Reference Guide: Chapter 3, Maintenance and Specifications

Maintaining the LS 1000 Scanner

Battery Box Operation

When using the LS 1000 Series with a battery box, you can use either an alkaline battery

(recommended), or a nickel-cadmium rechargeable battery. Low power is signalled by

4 short, high-tone beeps, coupled with scanning interruptions. If this occurs, change or

recharge the battery as soon as possible. For battery box operation:

1. Insert a 9-volt battery into the battery box.

2. Plug the scanner ’s 9-pin connector at the end of the coil cord into the end of the

battery box.

3. An output cable from the battery box connects the LS 1000 Series to the host device.

Connect one end of this cable to the battery box and the other to the appropriate

port on the host device.

Note:

Not all applications require a power supply or battery

box. The output cable depends on the wand being

replaced. See the

Product Ordering Guide

for more

information.

Changing the Battery

• Disconnect the battery box.

• To open the battery box, push up on the ﬂanges at one end of the pack.

• Remove the old battery.

• Insert the new or recharged 9-volt battery into the battery box. Match the

positive (+) and negative (-) terminals on the battery with the corresponding

terminals in the battery box.

Recharging a Nickel-Cadmium Battery

• Remove the battery from the battery box and place it in the recharging unit (not

supplied by Symbol).

• To recharge the battery, follow the instructions supplied with the recharging

unit.

coverBook Page 2 Monday, December 1, 1997 2:19 PM

Contents

Main LS 1000 Product Reference Guide Page Factory Service Symbol Support Center SYMBOL SUPPORT CENTER 1-800-653-5350 Contents Chapter 4. Programming The LS 1004 Chapter 3. Maintenance & Specifications Chapter 2. Scanning Page Chapter 1 Introduction and Set-up Introduction Page Set-Up LS 1000 Product Reference Guide: Chapter 1, Introduction and Setup Switching Cables Connecting to a Host For external power operation with Synapse Smart Cable RS-232C Page Page RS-232C (Contd) For battery operation: IBM 468X/9X IBM 468X/9X (Contd) Page Page Ready, Test, Scan Aiming Scan the Entire Symbol Hold at an Angle Page Maintaining the LS 1000 Scanner Recharging a Nickel-Cadmium Battery Changing the Battery Battery Box Operation Maintenance Accessories Optional Accessories Required Accessories What If... 3-6 LS 100x Technical Specications Depth of Field in Inches/Centimeters Figure 3-1. LS 100x Decode Zone LS 100x Decode Zone 3-7 Table 3-1. Technical Specications (LS 1000) 3-8 Table 3-1. Technical Specications (LS 1000) (Continued) 3-9 Table 3-2. Technical Specications (LS 1004) Page Page 3-12 * active low Table 3-4. Pinouts - LS 1004 3-13 Table 3-5. Beeper Indications Page 4-2 4-3 4-4 Scanning Sequence Scanning Sequence Example Errors While Scanning Parameter Descriptions Set Parameter Defaults Host Interface Select Page Page Decode Attempt Time Page Transmit No Decode Message Decode Redundancy Code Types UPC/EAN Convert UPC-E to UPC-A EAN Zero Extend Decode UPC/EAN Supplemental UPC A and E Preamble(s) UPC-E Pream- UPC-A Pream- UPC/EAN Security Level Code 128 Enable/Disable Code 128 Send CODE 128 Function Character Code 39 Page Interleaved 2 of 5 Enable/Disable Code I 2 of 5 Fixed Lengths for Code I 2 of 5 4-22 Fixed Lengths for Code 2 of 5 (contd) I 2 of 5 Modulo 10 Check ITF14/EAN13 Conversion Discrete 2 of 5 Enable/Disable D 2 of 5 D 2 of 5 Modulo 10 Check Fixed Lengths for Code 2 of 5 4-25 Fixed Lengths for Code 2 of 5 (contd) Codabar Data Options Transmit Code ID Character Prex Sufx 4-30 Prex/Sufx Values RS-232C Baud Rate Parity Data Format Stop Bit Select Check Parity Hardware Handshaking Software Handshaking Page 4-37 Hardware and Software Handshaking Sequence HARDWARE HANDSHAKING SOFTWARE HANDSHAKING Page 4-39 Intercharacter Delay Values (contd) Chapter 5 Glossary Page Page Page 6-1 Chapter 6 ASCII Character Set ASCII Character Set Table 6-1. ASCII Character Set 6-2 PPT 4600 Product Reference Guide: Getting Started Table 6-1. (Continued) ASCII Character Set 6-3 PPT 4600 Product Reference Guide: Getting Started Table 6-1. (Continued) ASCII Character Set A-1 Appendix A Errata Table A-1. ASCII Character Set A-2 A-3 Page Tell Us What You Think...