Manuals / Brands / Computer Equipment / Barcode Reader / Symbol Technologies / Computer Equipment / Barcode Reader

Symbol Technologies LS 1000 3-9, Table 3-2. Technical Specications (LS 1004)

1 85

Download 85 pages, 1.07 Mb

3-9

LS 1000 Product Reference Guide: Chapter 3, Maintenance and Specifications

Table 3-2. Technical Speciﬁcations (LS 1004)

Item Description

Power Requirements*

RS-232C/Synapse

Low Power

4.75 to 14.5 VDC (max) 100mA @ 5VDC typical

4.75 to 14 VDC (max) 200 mA @ 5V typical

Decode Capability The LS 100x can be programmed to decode the

following code types: UPC/EAN, Code 39,

Code 39 Full ASCII, Code 93, Codabar,

Interleaved 2 of 5, Code 128, EAN 128, and

Discrete 2 of 5. Set code length(s) for any linear

code type. The LS 100x can auto-discriminate

between all of the above code types except for

Code 39 and Code 39 Full ASCII.

Beeper Operation User-selectable: Enabled, Disabled., Volume, Tone

Scan Repetition Rate 36 (± 3) scans/sec (bidirectional)

Skew Tolerance ± 65˚ from normal

Pitch ± 60˚ from normal

Decode Depth of Field See Decode Zone

Print Contrast Minimum 25% absolute dark/light differential, measured at

670 nm.

Ambient Light Immunity

Artiﬁcial Lighting

Sunlight

450 ft. candles 4844 lux

8000 ft. candles86112 lux

coverBook Page 9 Monday, December 1, 1997 2:19 PM

Contents

Main LS 1000 Product Reference Guide Page Factory Service Symbol Support Center SYMBOL SUPPORT CENTER 1-800-653-5350 Contents Chapter 4. Programming The LS 1004 Chapter 3. Maintenance & Specifications Chapter 2. Scanning Page Chapter 1 Introduction and Set-up Introduction Page Set-Up LS 1000 Product Reference Guide: Chapter 1, Introduction and Setup Switching Cables Connecting to a Host For external power operation with Synapse Smart Cable RS-232C Page Page RS-232C (Contd) For battery operation: IBM 468X/9X IBM 468X/9X (Contd) Page Page Ready, Test, Scan Aiming Scan the Entire Symbol Hold at an Angle Page Maintaining the LS 1000 Scanner Recharging a Nickel-Cadmium Battery Changing the Battery Battery Box Operation Maintenance Accessories Optional Accessories Required Accessories What If... 3-6 LS 100x Technical Specications Depth of Field in Inches/Centimeters Figure 3-1. LS 100x Decode Zone LS 100x Decode Zone 3-7 Table 3-1. Technical Specications (LS 1000) 3-8 Table 3-1. Technical Specications (LS 1000) (Continued) 3-9 Table 3-2. Technical Specications (LS 1004) Page Page 3-12 * active low Table 3-4. Pinouts - LS 1004 3-13 Table 3-5. Beeper Indications Page 4-2 4-3 4-4 Scanning Sequence Scanning Sequence Example Errors While Scanning Parameter Descriptions Set Parameter Defaults Host Interface Select Page Page Decode Attempt Time Page Transmit No Decode Message Decode Redundancy Code Types UPC/EAN Convert UPC-E to UPC-A EAN Zero Extend Decode UPC/EAN Supplemental UPC A and E Preamble(s) UPC-E Pream- UPC-A Pream- UPC/EAN Security Level Code 128 Enable/Disable Code 128 Send CODE 128 Function Character Code 39 Page Interleaved 2 of 5 Enable/Disable Code I 2 of 5 Fixed Lengths for Code I 2 of 5 4-22 Fixed Lengths for Code 2 of 5 (contd) I 2 of 5 Modulo 10 Check ITF14/EAN13 Conversion Discrete 2 of 5 Enable/Disable D 2 of 5 D 2 of 5 Modulo 10 Check Fixed Lengths for Code 2 of 5 4-25 Fixed Lengths for Code 2 of 5 (contd) Codabar Data Options Transmit Code ID Character Prex Sufx 4-30 Prex/Sufx Values RS-232C Baud Rate Parity Data Format Stop Bit Select Check Parity Hardware Handshaking Software Handshaking Page 4-37 Hardware and Software Handshaking Sequence HARDWARE HANDSHAKING SOFTWARE HANDSHAKING Page 4-39 Intercharacter Delay Values (contd) Chapter 5 Glossary Page Page Page 6-1 Chapter 6 ASCII Character Set ASCII Character Set Table 6-1. ASCII Character Set 6-2 PPT 4600 Product Reference Guide: Getting Started Table 6-1. (Continued) ASCII Character Set 6-3 PPT 4600 Product Reference Guide: Getting Started Table 6-1. (Continued) ASCII Character Set A-1 Appendix A Errata Table A-1. ASCII Character Set A-2 A-3 Page Tell Us What You Think...