Taylor C708, C716 - page 45

41

Models C708 & C716 Operating Procedures

100507

Step 4

Install the pump assembly at the rear of the mix

hopper. To position the pump on the drive hub, align

the drive hole in the piston with the drive crank of

the drive shaft. Secure the pump in place by slipping

the pump clip over the collar of the pump, making

surethe clip fits into the grooves in the collar.

(See Figure 44.)

Figure 44

Step 5

Installthe pump end of the mix feed

tube and secure with the cotter pin . Failure to

follow this instruction could result in sanitizer

spraying on the operator. (See Figure 45.)

Figure 45

Step 6

Prepare another pail of approved 100 PPM sanitiz-

ing solution (examples: 2-1/2 gal. [9.5 liters] of

Kay-5Ror 2 gal. [7.6 liters] of Stera-SheenR).

USE WARM WATER AND FOLLOW THE MANU-

FACTURER'S SPECIFICATIONS.

Step 7

Pour the sanitizing solution into the mix hopper.

Step 8

Brush the exposed sides of the hopper.

Step 9

Place the power switch in the ON position.

Step 10

Touch the WASH symbol . This will cause the

sanitizing solution in the freezing cylinder to be

agitated. Wait at least 5 minutes before proceeding

with these instructions.

Step 11

With a pail beneath the door spout(s), open the draw

valve and touch the PUMP symbol . Open and

close the draw valve 6 times.

Note: Momentarily open the center draw valve to

sanitize the center door spout (C716 only).

Draw off the remaining sanitizing solution.

Step 12

Touch the WASH and PUMP symbols and

close the draw valve. (See Figure 46.)

Figure 46

Note: Be sureyour hands are clean and

sanitized before going on in these instru ctions.

Contents

Main Page Table of Contents Table of Contents - Page 2 Section 1 To the Installer Installer Safety S Site Preparation Air Cooled Units Water Connections Electrical Connections S Beater Rotation Refrigerant Section 2 To the Operator Compressor Warranty Disclaimer Section 3 Safety S Page Page Model C708 Exploded View Parts Identification Page Model C716 Exploded View Parts Identification 12 Models C708 & C716Operator Parts Identification Model C708 Single Spout Door and Beater Assembly Figure 3 13 Model C716 Door and Beater Assembly Figure 4 14 Models C708 & C716Operator Parts Identification X57029-XX Pump A. - Mix Simplified (Models C708 & C716) Figure 5 15 Accessories Figure 6 16 Models C708 & C716Operator Parts Identification Brush A.-Package-HT X44127 Figure 7 Section 5 Important: To the Operator C708 C716 Symbol Definitions Power Switch Fluorescent Display Indicator Lights Reset Mechanism Operating Screen Descriptions Power Up Memory (Initializing) Page Power Switch OFF Power Switch ON International Models Only: Heat Cycle Freezer Locks Hardlock Soft Lock Manager's Menu S Entering Access Code Manager Menu Options Exit From Menu Servings Counter Set Clock Auto Heat Time Auto Start Time Standby Mode Mix Level Audible Fault Description Fault History Lockout History Faults Occurring Entering a Heat Treatment Cycle Faults Occurring While in Heat Mode Faults Occurring While in AUTO Mode Heat Cycle Summary Heat Cycle Data Page System Information Current Conditions Net Service Pin Section 6 Operating Procedures Freezing Cylinder Assembly Page Freezer Door Assembly Model C708 Freezer Door Assembly Page Model C716 Freezer Door Assembly Mix Pump Assembly Page Page Sanitizing Page Priming Daily Closing Procedures This procedure must be performed once daily! Daily Opening Procedures Set-Up - Complete The Following Manual Brush Cleaning S S S S Draining Product From The Freezing Cylinder Rinsing Hopper Cleaning Disassembly Brush Cleaning Section 7 Important: Operator Checklist During Cleaning and Sanitizing Troubleshooting Bacterial Count Regular Maintenance Checks Winter Storage Section 8 Troubleshooting Guide Page Page Page Section 9 Parts Replacement Schedule Section 10 Parts List QTY. WARR. QTY. C716 NUMBER C708 DESCRIPTION PART