Technicolor - Thomson 42PB120S5 Programming the remote control, Automatic code search

42PB120S5-EN2 22/03/05 15:37 Page 7

Connections and Set-up

	Video recorder	DVD player	Satellite receiver	Hi-fi system
	Press the VCR button	Press the DVD button	Press the SAT button	Press the AMP button
	On/Standby	On/Standby	On/Standby	On/Standby
MENU	To display the main menu	To display the main menu	To display the main menu
	Vertical scrolling in menus	Vertical scrolling in menus	Vertical scrolling in menus
	Horizontal scrolling	Horizontal scrolling	Horizontal scrolling
	in menus	in menus	in menus
OK	To confirm an action	To confirm an action	To confirm an action
EXIT	To close a menu	To close a menu	To close a menu
0-9	To directly access channels	To enter numeric values	To directly access channels	To select a station using
	or enter numeric values	or select options in menus	or enter numeric values	its number
PR+/PR-	To change channels	To change chapters	To change channels	To change stations
AV	To select av input	To select av input
REV	Rewind	Rewind
PLAY	Play	Play
FWD	Fast forward	Fast forward
STOP	Stop	Stop
PAUSE	Pause picture	Pause picture
REC	Record
				To switch the sound off and
				back on again
+/-				To set the volume level

EN

Programming the remote control

Automatic code search

This method can be used to automatically find the most appropriate code for your appliance.

1.Switch on the appliance you wish to use the remote control with.

2.Press the relevant button for this appliance on the remote control, and while holding this button down, press the standby button until the light or the appliance buttons of the remote control come on. Release both buttons.

3.Point the remote control at the appliance and press PLAY. Wait until the light stops flashing. If the appliance has not gone into standby mode, press the PLAY button again to continue the search for the next set of codes. Repeat this operation until the appliance goes into standby mode.There are around 20 sets of codes.

4.When the appliance goes into standby mode, switch it on again without using the remote control. Press the REV button as many times as is required to return the appliance to standby mode.

5.Press the STOP button and hold it down until the light or the appliance buttons of the remote control go off.

Note:You can cancel the programming operation at any time by pressing the EXIT button.

Manual programming

This method involves carrying out a manual search for the codes to be used for controlling your other appliances.

1.Switch on the appliance you wish to use the remote control with.

2.Press the relevant button for this appliance on the remote control, and while holding this button down, enter one of the codes relevant to your make of appliance (there is a list of codes at the end of this manual). If the light or the appliance buttons of the remote control flash you have entered the wrong code or it is not possible to program the remote control.

3.Point the remote control at the appliance and press the

relevant button (VCR, DVD, etc). Press the standby button. If the appliance does not go into standby mode, try another code.

Depending on the year of manufacture and the type of appliance, some functions may not be available. Certain codes may cover more functions than others.Test the functions you can control and, if appropriate, try other codes.

Note here the	VCR	AUX
code(s) which work	DVD	AMP
best.	SAT

When you change the remote control’s batteries, remember to reprogram it.

Programming the volume control function

If you have programmed the TV remote control to use with other appliances and these are connected to an amplifier you can also programme the remote control to adjust the volume when you are using one of these appliances.The example below describes the procedure for programming a DVD player.

1.Programme the AMP button on the remote control to use with the amplifier (refer to page 6).

2.Move the remote control away from the appliances. Press the

- button and while holding it down, press the relevant mode button (DVD, in this example), then the AMP button. Release the - button.

3.Switch on the amplifier, then the DVD player.

4.Set the remote control to DVD, play a disc and adjust the volume using the +/- buttons.

Repeat this operation for the other appliances.

To cancel the programmed function for any of the appliances, press the - button, while holding it down and enter the code 000 using the numeric buttons.

7