TechniSat® VC 2002 S

REMOTE CONTROL

POWER ON/OFF

KEY PAD

STORE

ERASE

DEVIATION HIGH/LOW BRIGHTNESS

V/H POLARISATION

DECODER (NORMAL/DECODER MODE) DECODER SIGNAL SELECTION (D1-D4)

An/Aus

M

MUTE

 

1

 

2

 

 

 

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

AUDIO UP/DOWN (FOR SUBCARRIER

 

 

 

 

 

 

 

 

 

 

 

 

AUDIO

 

4

 

5

 

 

 

6

 

 

 

 

 

 

 

 

FREQUENCY 5.0 - 8.80 MHz)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MONO/ST

 

 

 

 

 

 

 

 

7

 

8

 

 

 

9

 

 

 

 

 

 

 

 

MONO/STEREO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

STORE

 

 

 

 

ERASE

 

 

A/B

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0

 

 

 

 

 

 

 

 

 

 

 

 

A/B: LEFT/RIGHT STEREO (USED WITH AUDIO UP/DOWN)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DEV.

 

 

 

V/H

 

 

 

 

W/N

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DE-EMPHASIS (WIDE - TV-SOUND, NARROW - RADIO)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DECODER

D.MODE

TUNING

CH

CHANNEL UP/DOWN

 

 

 

VIDEO FREQUENCY UP/DOWN (950-2050 MHZ)

TechniSat

INSTALLATION & INITIAL OPERATION

1.Connect the receiver VC 2002 S to the LNB of the outdoor unit using a coaxial cable via IF-IN connection.

CAUTION: Always ensure that the mains supply is off when making any connections (including LNB connection).

2.The connection between receiver and TV is made using a scart cable. Alternatively, you can make the connection using an antenna cable.

3.Connect the receiver to the mains supply (240 V/50 Hz).

4.i) If you are using a scart cable connection, switch your TV to AV.

ii)If UHF cable connections are being used it is necessary to find a suitable UHF channel. The satellite receiver is preprogrammed to channel

36.To set the TV or VCR to this channel select TSG on the receiver back panel and search on the TV until two vertical white bars are clearly visible. If due to interference it is necessary to adjust the UHF channel, this can be done using the channel adjustment switch on the back of the receiver (by turning the screw).

5

Page 5
Image 5
TechniSat VC 2002 S manual Installation & Initial Operation, Remote Control