Notice_NC00023715_notice 19/07/11 15:19 Page18
Note:
You can change the initial temperature at any time by pressing the buttons
You can stop the heating process at any time by pressing the
•When the water reaches the selected temperature, 2 series of 3 beeps will be heard, a red light goes off and the kettle stops automatically.
If you programmed the temperature under 100°C, the kettle will start the heating cycle, then stop for few seconds in order to verify the current temperature and adjust the needed heating incoming time. Then, it will resume to reach the temperature of your choice.
N.B.:
-During the heating cycle, if you remove the kettle from its base, the heating parameters you selected remain in the memory and active. Therefore, when you put the kettle back in place, the heating cycle starts again at the temperature you selected. You can, for example, remove the kettle from its base to add more water in the middle of the heating cycle. When you put the kettle back on the base, the heating cycle will resume as normal. However, if the kettle is disconnected for more than 10 minutes from the base, it will shut off automatically.
-Do not leave water in the kettle after use.
-When you have finished using the kettle and you put it back on its base, ensure that the heating cycle has been completed and that the electronic base is switched off in order to prevent the kettle boiling dry.
USING THE TIMER "KEEP WARM" FUNCTION
Your electronic kettle has a "Keep Warm" function which makes it possible to keep your water at the selected temperature for the duration of your choice.
a) Setting the initial heating temperature
First of all, using the "/
b) Setting the keep warm function: temperature and time
-Press the keep warm button once: the temperature will be displayed and will flash: 90°C max. (The first time you use the keep warm function, 80°C is displayed. When it is later used, the temperature programmed for the most recent Keep Warm cycle is displayed).
-Select the desired temperature using the +/- buttons (between 60°C and 90°C).
-Press the keep warm button once the time in minutes is displayed and flashes 60 minutes max.
-Select the time for keeping warm using the +/- buttons (between 10 and 60 minutes)
-Press the keep warm button again to confirm: display of the keep warm + clock
(
) logos: activation of the keep warm function (fig. B) Press the On/Off button to start the heating cycle.
18
Note:
You cannot select a keep warm temperature higher than the temperature used for the heating cycle.
The keep warm cycle duration is expressed in minutes and cannot be less than 10 minutes or more than 60 minutes.
The heating cycle starts
•The red light comes on.
•The heating temperature is displayed along with the Keep Warm logo.
•You can still at any time change the temperature of the heating cycle, provided it remains higher than the preset temperature for the Keep Warm cycle.
•Once the heating cycle is complete, 2 series of 3 beeps will be heard.
The keep warm cycle begins
•The red light flashes
•The keep warm temperature, the keep warm logo, the keep warm cycle duration and the time logo (
) are displayed.
•When the keep warm cycle is completed, 2 series of 3 beeps will be heard, the red
light goes off and the kettle stops automatically.
Note:
-The keep warm time indicated on the screen is the time left in the keep warm cycle.
-You can still modify the keep warm time using the +/- buttons
-You cannot change the keep warm temperature
-During the keep warm cycle, if you remove the kettle from its base, the keep warm parameters you selected remain in the memory but the time continues to count down. If the kettle is disconnected for more than 10 minutes from the base, it will shut off automatically.
-Do not leave water in the kettle after use.
-When you have finished using the kettle and you put it back on its base, ensure that the keep warm cycle has been completed and that the electronic base is switched off in order to prevent the kettle boiling dry.
-You can stop the keep warm cycle at any time by pressing the
Cleaning and maintenance
Do not leave water in the kettle after use, because this accelerates the deposit of scale
To clean your kettle
•Unplug it.
•Let it cool down and clean it with a damp sponge.
Never immerse the kettle, its base, the power cord or the plug in water: the electrical connections and the switch must not come into contact with water.
Do not use scouring pads.
19
