Tektronix vx4380 INITiate

Command Descriptions

VX4380 256-Crosspoint Relay Matrix Module User Manual 3–23

INITiate

INITiate

[:IMMediate]

N/A

N/A

The trigger subsystem is in the idle state.

ABORt

ROUTe:SCAN

TRIGger[:SEQuence][:SOURce]

TRIGger[:SEQuence][:IMMediate]

TRIGger[:SEQuence][:COUNt]

TRIGger[:SEQuence][:DELay]

This command places the trigger subsystem in the armed state. In this state, a

trigger event enabled by the TRIGger[:SEQuence][:SOURce] command closes

the next relay in a scan sequence, after opening the previous relay in the

sequence. After a sufficient number of triggers have been received to cycle

through a scan list the number of times specified in a TRIGger:[SEQuence]

:COUNt command, the trigger subsystem is placed in the idle state. In this state,

triggers are ignored.

In this example, module names “m1” and “m2” have been assigned to VX4380

Modules.

Command Response

route:scan

(@m1(1!1!1),

m2(1!1!1,1!1!2))

Define a scan list consisting of 3 relays.

trigger:sequence:

count 1

Define the number of times to sequence through the scan list

before setting the state of the trigger subsystem back to the

idle state.

initiate:immediate Initiate the scan sequence.

trig Close the first relay in the sequence.

trig Open the first relay and close the second relay in the

sequence.

Command Syntax

Query Syntax

Query Response

*RST Value

Related Commands

Description

Examples

Contents

Main Page WARRANTY Page Table of Contents Getting Started Operating Basics Syntax and Commands Status and Events Page General Safety Summary Injury Precautions Product Damage Precautions Safety Terms and Symbols Certifications and Compliances Page Page Preface Conventions Page Page Page Getting Started Product Description Page Getting Started = Figure 11: VX4380 Functional Block Diagram VX4380 256-Crosspoint Relay Matrix Module User Manual 13 = Fuses Accessories Controls and Indicators Switches LEDs BITE (Built-in Test Equipment) Page Configuration Logical Address Switches IEEE-488 Address VMEbus Interrupt Level Select Switch Installation Tools Required Requirements and Cautions Installation Procedure Installation Checklist Functional Check Self Test Operational Check SYSFAIL* Operation Page Page Page Operating Basics Functional Overview Power-on Instrument I/O: VXIbus Basics Configuration Registers Page Page Page Command Syntax Page Syntax Example SCPI/IEEE 488.2 Command Elements Page Page Page Page Page Page Functional Command Groups System Commands Module Commands Functional Command Groups 312 VX4380 256-Crosspoint Relay Matrix Module User Manual Table 31: Summary of VX4380-Specific SCPI Commands Table 32: Summary of IEEE-488.2 Common Commands Functional Command Groups VX4380 256-Crosspoint Relay Matrix Module User Manual 313 Table 32: Summary of IEEE-488.2 Common Commands (Cont.) Page Command Descriptions ABORt Page CLOSe Page Page Page ID? INITiate Page Page MODule Page Page Page OPEN Page Page Page Page OUTPut PFAil SCAN Page Page Command Descriptions 340 VX4380 256-Crosspoint Relay Matrix Module User Manual STATus Page Page Page SYSTem Page Page Page TRIGger Page Page Page IEEE-488.2 Common Commands *CLS *ESE <NRf> *ESE? *ESR? *IDN? *OPC *OPC? *RST *SRE <mask> *SRE? *STB? *TRG *TST? *WAI Page Page Page Status and Events Status and Event Reporting System Status Byte Register Service Request Enable Standard Event Status Event Status Enable The Output Queue The System Error and Event Queue Status and Events VX4380 256-Crosspoint Relay Matrix Module User Manual 45 Status and Event Reporting Process Messages Page Page Page Page VX4380 256-Crosspoint Relay Matrix Module User Manual A1 Appendix A: Specifications Table A1: VXI Instrument Characteristics A2 VX4380 256-Crosspoint Relay Matrix Module User Manual Table A1: VXI Instrument Characteristics Table A2: Environmental/Reliability Characteristics Table A3: VX4380-Specific Characteristics VX4380 256-Crosspoint Relay Matrix Module User Manual A3 Table A3: VX4380-Specific Characteristics (Cont.) Table A4: Relay Switching Characteristics A4 VX4380 256-Crosspoint Relay Matrix Module User Manual Table A5: Switching Channel Characteristics Table A6: Signal Path Table A7: Cabling Table A7: Power Distribution Page Page Appendix B: Input/Output Connections VX4380 256-Crosspoint Relay Matrix Module User Manual B3 Table B1: VX4380 Upper Connector (J401) Pinout Appendix B: Input/Output Connections B4 VX4380 256-Crosspoint Relay Matrix Module User Manual Table B2: VX4380 Lower Connector (J1201) Pinout Page Page Appendix C: Examples Example 1 Page Page Example 2 Appendix D: User Service Performance Verification Preventive Maintenance Troubleshooting Page Appendix E: Replaceable Parts Parts Ordering Information Module Servicing Using the Replaceable Parts List Abbreviations Mfr. Code to Manufacturer Cross Index VX4380 256-Crosspoint Relay Matrix Module User Manual E3 Manufacturers Cross Index Mfr. Code Manufacturer Address City, State, Zip Code E4 VX4380 256-Crosspoint Relay Matrix Module User Manual Replaceable Parts List Effective Serial No. Part Number Serial No. Fig. & Index Number Tektronix VX4380 256-Crosspoint Relay Matrix Module User Manual E5 Figure E1: VX4380 Exploded View Page Page Page Glossary Page Page Page Page Page Page Page VX4380 256-Crosspoint Relay Matrix Module User Manual Index1 Index A C D E T W