Manuals / Brands / Baby / Model Vehicle / Teledyne / Baby / Model Vehicle

Teledyne 401 11.2 Spare Parts For Non-CE Mark Units

1 114

Download 114 pages, 1.08 Mb

Teledyne API Model 401 O3 Photometric Calibrator Instruction Manual, 01124, Rev. J2

11.2 Spare Parts For Non-CE Mark Units

Table 11-2: Spare Parts For Non-CE Mark Units

Part No. Description

00015 Power Supply Board

00276-0401 CPU Board

00402-03 Sensor Board

00508 Absorption Tube

00514-03 V/F Board

00526-01 U V Lamp Assy, Sourc e

00535 Pre-Amp Assy, M 400 DET

00551-03 Power Supply Module - 115 V/60 Hz

00551-13 Power Supply Module - 220 V/50 Hz

00551-19 Power Supply Module - 240 V/50 Hz

00566-02 A s sy, Optical Benc h

00596 Activated Charcoal

00611 Assy, Heater/Thermistor

00612-01 U V Lamp Assy, IZS Gen

00628 Assy, Heater, 5 0 W (IZS)

00690-01 Scrubber Pads

00704 Keyboard

00728 Display

00815 M400 Valve Module

01061 M401 Pump

01111 M401 Level 1 Spares Kit

01112 M401 Expendables Kit

01509 UV Lamp Power Supply

01934 Assy, Sample Thermistor

CB004 Fuse, 3 AG 3 AMP, 250 V

FA004 Fan

FL003 Filter, DFU (036-040180)

(table continued)

11-3

Contents

Main INSTRUCTION MANUAL MODEL 401 O3 CALIBRATOR SAFETY MESSAGES TABLE OF CONTENTS Page Page 10 ROUTINE MAINTENANCE........................................................................ 10-1 11 MODEL 401 SPARE PARTS AND EXPENDABLES KITS........................ 11-1 LIST OF FIGURES LIST OF TABLES 1 INTRODUCTION 1.1 Preface 1.2 Warranty 1.3 Principle Of Operation a l C n 1.3.1 Interferent Rejection 1.4 Specifications 1-5 Page 1.4.10 Flow Rates 1.4.11 Power 1.4.12 Weight 1.5 Installation And Overview Page Page Page Page Page Page 1.6 Electrical And Pneumatic Connections 1.6.1 Electrical Connections 1.6.2 RS-232 Page 1.6.3 Pneumatic System 1.6.4 Exhaust Connections (See Figure 1-5) 1.6.5 Output Flow Adjustment Page Page Page 1.7 Operation Verification 1.7.1 Final Test And Calibration Values 1-21 Table 1-1: Test Values 1.8 Options 2 OPERATION 2.1 Key Features 2.1.1 O3 Readout 2.1.2 O3 Analog Output 2.1.3 E2 ROM Backup Of Software Configuration 2.1.5 Data Acquisition 2.1.6 RS-232 Interface 2.1.7 Password Protection Page 2.2 Front Panel 2.2.1 Front Panel Display Page Table 2-3: Test Measurements 2-6 2.2.2 Programmable Pushbuttons Page 2.2.3 Status LEDs Page 3 CALIBRATION 3.1 Manual Zero Air Supply 3.2 Manual O3 Generation 3.3 Automatic Zero/Span (or Multipoint) Check 3.4 Manual Zero/Span (or Multi-Point) Check 3.5 Summary Of Front Panel Calibration Controls 3.6 Photometer Calibration 3.7 Remote Zero/Span Check (Contact Closure) 3.8 Remote Zero/Span Check Or Adjustment (RS-232) 3.9 Hold Off Page 4 SETUP MODE 4.1 Setup Mode Operation 4.2 Setting Automatic Multipoint (ASEQ) Check 4.3 Setting Automatic Zero/Span Duration 4.4 Examining The Ozone Formula Slope And Offset + = 4.5 Setting the O3 Generation Mode 4.5.1 BNCH Mode 4.5.2 REF Mode 4.5.3 CNST Mode 4.6 Setting The Time-Of-Day 4.8 Adjusting The Clock Speed 4.9 Setting The O3 Concentration Range 4.10 Setting The Analog Output Offset 4.11 Setting The RS-232 Baud Rate 4.12 Setting The Analyzer I.D. 4.13 Disabling The Calibration Password 4.14 Setting The Fault LED Timeout Page Table 4-1: Setup Variables 4-7 Page 5 DIAGNOSTICS 5.1 Test Measurements 5.2 Diagnostic Tests 5.2.1 D/A Output 6 HANDLING WARNINGS Page 7 RS-232 COMMUNICATIONS 7.1 DAS Reporting 7.2 Warnings 7.3 Status/Control Page 7.4 Diagnostics 7.5 Test Measurements 7.6 Viewing And Modifying Variables Page Page 8 ADJUSTMENTS 8.1 Power Supply Board Adjustment 8.1.1 Box Temperature Limits Page 8.2 A/D - D/A Calibration Procedure 8.3 Output Voltage Range Changes 8.4 Flow Readout Adjustment Page 8.5 DC Power Supply 8.6 CPU 8.7 Status Lines 8.8 UV Lamp Power Supply Adjustment 8.9 Ozone Generator Lamp Setup 8.10 Ozone Generator Calibration 8.11 Dark Current Signal Adjust Procedure 8.12 Bench Feedback Option Teledyne API Model 401 O3 Photometric Calibrator Instruction Manual, 01124, Rev. J2 9 TROUBLESHOOTING 9.1 Overview 9.2 Troubleshooting Fundamental Calibrator Operation 9.2.1 Checking The Power Sub-Systems 9.2.2 Checking The CPU And Display 9.2.3 Checking The Keyboard 9.3 Troubleshooting Using Warning Messages 9-4 9.4 Troubleshooting Using Test Function Values 9.5 Troubleshooting Dynamic Problems 9.5.1 Noisy Or Unstable Readings At Zero 9.5.2 Noisy, Unstable, Or Non-Linear Span Readings 9.5.3 Slow Response To Changes In Concentration 9.5.4 Analog Outputs Do Not Agree With Front Panel Readings 9.5.5 Cannot Zero 9.5.6 Cannot Span 9.6 Troubleshooting Individual Sub-Assemblies And Components 9.6.1 Troubleshooting Flow Problems 9.6.2 Troubleshooting Temperature Problems 9.6.3 Checking The V/F Card Page 9.6.4 Checking The DC Power Supply Board 9.6.5 Checking The Pneumatic Sensor Board 9.6.6 Checking The Source Lamp And Detector Page 9.6.7 Checking Main Switching Valve 9.6.8 Checking The Lamp Power Supply Page Teledyne API Model 401 O3 Photometric Calibrator Instruction Manual, 01124, Rev. J2 Warranty/Repair Questionnaire 9-18 9.7 Warranty/Repair Questionnaire ____________________________________________________________________________________ Teledyne API Model 401 O3 Photometric Calibrator Instruction Manual, 01124, Rev. J2 10 ROUTINE MAINTENANCE 10-1 10.1 Maintenance Schedule 10.2 Leak Checking 10.3 Cleaning Of Sample Cell 10.4 Changing The Prom Page 11 MODEL 401 SPARE PARTS AND EXPENDABLES KITS 11.1 Spare Parts For CE Mark Units 11-2 Teledyne API Model 401 O3 Photometric Calibrator Instruction Manual, 01124, Rev. J2 11.2 Spare Parts For Non-CE Mark Units 11-3 Table 11-2: Spare Parts For Non-CE Mark Units Page Appendix A LIST OF AVAILABLE MODEL 401 OPTIONS Page Appendix B RECOMMENDED ZERO AIR SYSTEM Page Appendix C REFERENCES Page Page Page Appendix E ELECTRICAL SCHEMATIC INDEX