suggested that all connections be checked for leaks after installation. This can be done by pressurizing the instrument (do not exceed 500 psig unless the Flowmeter is specifically rated for higher pressures) and applying a diluted soap solution to the flow connections rated for higher pressures) and applying a diluted soap solution to the flow connections.

2.5.Electrical Connections

If a power supply from Hastings Instruments is used, installation consists of connecting the HFM-E- 200/HFC-E-202 series cable from the “D” connector on the rear of the power supply to the “Edge” connector on the top of the Flowmeter. If a different power supply is used, follow the instructions below when connecting the flow meter.

This HFM-E-200/HFC-E-202 series requires Hastings cable #65-854. Use of any other cable can severely damage the instrument and void the warranty. Figure 2.1 shows the schematic layout for connecting the instrument to an appropriate power supply.

The power supply used must be capable of supplying +15VDC at 50mA and -15VDC at -200mA for each controller. These voltages must be referenced to a circuit Common terminal. Connect -15VDC to pin F and +15VDC to pin 4.

Pins 2, B and C are all Commons and they are connected together internally with solder jumpers to ensure compatibility with legacy flow controllers. At least one of these Common pins must be connected to the Common pin on the power supply. However for new designs and for installations with long cable runs between the transducer and the power supply it is recommended that pin C be isolated from the other Common pins of the transducer and provided a separate wire to connect it to the power supply Common.

Figure 2.1

This pin carries the valve current and under conditions when the impedance of the wire connecting the transducer Common to the power supply Common is high, tying these Commons together at the transducer can create cross-talk that may result in flow instabilities or errors in the Command signal or the Flow Output signal. In order to isolate pin C, solder jumpers JP8 and JP10 must be unsoldered while JP7 remains soldered. This will be performed at assembly time in the factory if there is an indication at the time of order that this is desired or it can be performed in the field. The Common pins can be reconfigured to put the valve return current on different pins. Consult factory if it is necessary to match previously installed wiring.

HFM-E-200/HFC-E-202

Page 8 of 30

Page 7 Page 9
Page 8
Image 8
Teledyne HFC-E-202, HFM-E-200 instruction manual Electrical Connections
Page 7 Page 9

HFC-E-202, HFM-E-200 specifications

Teledyne HFC-E-202 and HFM-E-200 are advanced flow meters designed to provide precise measurement and monitoring of gas and liquid flows in various industrial applications. Both devices are engineered to meet the demands of sectors such as petrochemicals, pharmaceuticals, and food and beverage, where accuracy and reliability are paramount.

The Teledyne HFC-E-202 is a highly sensitive flow meter that utilizes a thermal mass flow measurement technology. This technology enables the HFC-E-202 to accurately measure the mass flow rate of gases regardless of temperature and pressure conditions. One of its key features is its ability to provide high precision and fast response times, making it suitable for applications that require immediate data feedback. The device is also equipped with advanced diagnostics that allow users to monitor the health of the system and identify potential issues before they escalate.

On the other hand, the HFM-E-200 is particularly renowned for its versatility in measuring both gas and liquid flows. It employs differential pressure technology, which is highly effective in a wide range of operating conditions. The HFM-E-200 incorporates a robust design that can withstand harsh environments, ensuring longevity and reliability. Its user-friendly interface allows for easy configuration and monitoring, catering to both novice and experienced technicians.

Both flow meters feature digital output options, facilitating seamless integration with existing control systems. This enables real-time data acquisition and monitoring, enhancing process control and efficiency. Furthermore, their compact design minimizes installation space, allowing for easy placement in tight operational areas.

In terms of safety and compliance, both the HFC-E-202 and HFM-E-200 are designed to meet strict industry standards, ensuring they can be deployed in critical applications without compromising safety.

In conclusion, Teledyne HFC-E-202 and HFM-E-200 flow meters stand out due to their innovative technologies, accuracy, and durability. Their unique features position them as essential tools for a variety of industrial sectors, enhancing operational efficiency and ensuring reliable fluid flow measurement. With Teledyne’s commitment to quality and innovation, users can trust that these devices will meet their demands both now and in the future.
Top Page Image Contents