Therma-Stor Products Group 135H owner manual 2B Setting, 2C On/Off Setting, 2D Setting Clock Time

•The word “CLOCK” appears at the top of the display during the clock display, along with the day and time.

•The word “HUMIDITY” appears during the humidity display, with the current setpoint on the left, and the ambient RH on the right.

•The word “TEMP” appears as the unit displays the current temperature.

•The fan status display is indicated by a capitol “F”. “OF” indicates fan off status, “on” indicates fan on status.

•The damper display is indicated by a “d” with the same on/off status indicators as the temperature.

•The ventilation program is displayed along the bottom of the display during the clock, humidity, and temperature dis- plays only when the damper operation is set to the pro- grammed setting “Pr”.

5.2B Setting

During the set-up process, if you make a mistake, you can always go back to adjust the settings. If you leave the control alone and don’t touch any buttons for 10 seconds, the con- trol will remember any changes made and return to “home state.”

5.2C On/Off Setting

Press the “ON/OFF” button to turn the system on or off. When the system is on, the green indicator will be lit. In the off mode, the controller continues the regular display sequence and indicates current time, temperature, and relative humidity. It also displays the status of the fan and damper as if the control were on, but the fan and damper will not operate unless the control is on and the green indicator is lit. Setup can be done with the control either on or off.

On/Off

Program

Clock

Fan

Damper

Hum

Figure 2: DEH 2000 User Panel

5.2D Setting Clock Time

1.Push “CLOCK” button. The hour display will flash, use the “SET” + or – buttons to adjust hour. Notice the a.m./p.m. display.

Figure 4: Fan Setting

2.Push “CLOCK” button again. The minute display will flash. Use the “+,–” buttons to adjust to the proper time.

3.Push “CLOCK” button again. The day display will flash. Use the “+,–” buttons to select the proper day.

4.Push “CLOCK” button again. The AM/PM display will flash. Verify AM/PM setting is correct.

5.Push “CLOCK” button again, or wait a few seconds for the display to stop flashing. The time is now set.

5.2E Setting Relative Humidity Setpoint

The relative humidity setpoint operates the dehumidifier function of the Ultra-Aire. It has no effect on any other func- tion of the unit. The control senses the ambient relative humidity of the space in which it is located. The ambient con- dition is displayed on the right in the relative humidity display sequence, under the word “HUMIDITY”. The current setpoint is displayed on the left, under the word “SET”.

Figure 3: DEH 2000 Clock DIsplay

If the setpoint is equal to or greater than the current ambient condition, the space does not need to be dried, so the dehu- midifier function will be off. Example: Setpoint: 50% RH Current condition 45% RH = Dehumidifier off, red “DEHU” indicator not lit.

If the setpoint is less than the ambient condition, the dehumidifier will be on, and the red “DEHU” indicator will be lit. The space is more humid than the setpoint, so the con- troller operates the dehumidifier to dry the space. Example: Setpoint: 50% RH Current condition: 55% RH = Dehumidifier on, red “DEHU” indicator lit.

To set the relative humidity setpoint, press the “HUM” button. The display will show the “HUMIDITY” display, and the word “SET” will flash. Use the “SET” + or – buttons to adjust the relative humidity setpoint as desired. Therma-Stor Products recommends relative humidity levels of 45% in the summer, and lower levels in the winter. It is not recommended the humidity setpoint be set below 35%. In order to dry the home in the winter in a cold climate, use the ventilation function of the system rather than the dehumidifier function.

Ultra-Aire 135H Air Purifying Dehumidifier Owners Manual 5