Toastmaster TC17A II. Installation, III. Operation, Assembly, Electrical Utility Connection

II. INSTALLATION

IMPORTANT

IT IS THE CUSTOMER’S RESPONSIBILITY TO REPORT ANY CONCEALED OR NON-CONCEALED DAMAGE TO THE FREIGHT COMPANY.

A.Assembly

ENGLISH	1.	Thread the 4” (102mm) legs into the four holes on the bottom of
		the toaster. See Figure 2. Then, place the toaster in the desired
		location.
	2.	Install the entry rack and crumb tray into the front of the toaster,
		as shown in Figure 2.
		Figure 2 - Basic assembly and front-exit configuration
		Entry rack
		hanger rods fit
		into holes on
		toaster body

Return tray

slides underneath

toaster

Legs (4)	Crumb tray
thread into holes	slides into opening
in bottom of	in front of toaster
toaster

3.TOASTERS INTENDED FOR FRONT-EXIT OPERATION ONLY:

Position the return tray underneath the toaster, as shown in Figure 2. Note that the return tray extends past the FRONT of the toaster in the front-exit configuration.

4.TOASTERS INTENDED FOR “STRAIGHT-THROUGH,” REAR- EXIT OPERATION ONLY:

•Remove the CENTER screw from the rear panel of the toaster, as shown in Figure 3.

•Push the rear panel forward into the toaster.

•Position the return tray underneath the toaster as shown in Figure 3. Note that the return tray extends past the REAR of the toaster in the rear-exit configuration.

Figure 3 - Electrical connection and rear-exit configuration

2. Adjust

panel

Serial

plate

1. Remove

screw

Return tray

slides underneath

toaster

B.Electrical Utility Connection

IMPORTANT

THE ELECTRICAL CONNECTION TO THE TOASTER REQUIRES A CIRCUIT BREAKER/FUSED DISCONNECT. ELECTRICAL SPECIFI- CATIONS ARE LISTED ON THE SERIAL PLATE (SHOWN IN FIG- URE 3), AND IN THE ELECTRICAL SPECIFICATIONS ON PAGE 1 OF THIS MANUAL.

CONSULT ALL APPLICABLE NATIONAL AND LOCAL CODES FOR FURTHER ELECTRICAL CONNECTION REQUIREMENTS.

1.Before proceeding with the electrical connection, check the following:

a.Check that the electrical supply matches the toaster’s requirements. Refer to the toaster’s serial plate (Figure 3) and to the Electrical Specifications on Page 1.

b.Check that the appropriate receptacle is available for the power cord plug.

WARNING

ENSURE THAT BOTH THE CIRCUIT BREAKER/FUSED DIS- CONNECT AND THE ON/OFF/STBY KNOB ARE IN THE OFF POSITION BEFORE PROCEEDING. ENSURE THAT ANY PACKING MATERIAL RESIDUE HAS BEEN REMOVED FROM INSIDE THE TOASTING CHAMBER.

2.Insert the power cord plug into its receptacle.

III. OPERATION

A.Location and Function of Controls

This section provides a basic description of the toaster controls, their location, and the functions they perform. The operator MUST be familiar with the controls. Refer to Figure 4.

Figure 4

1. ON/OFF/STBY	2. Conveyor	3. Top and Bottom
knob	speed control	temperature
	knob	adjustment knobs

1.ON/OFF/STBY knob

•When set to “ON,” turns on the conveyor and elements.

•When set to “OFF,” turns off the conveyor and elements.

•When set to “STBY,” places the toaster in a standby mode by reducing the power to the heating elements. This saves power during idle periods and extends the life of the toaster’s components. Switching the knob back to the “ON” position will return the toaster to operating temperature within 5 minutes.

2.Conveyor Speed control knob

Adjusts the speed of the conveyor belt.

•“SLOW” is the minimum speed setting.

•“FAST” is the maximum speed setting.

3.Top and Bottom temperature adjustment knobs

Adjusts the temperature of the heating elements. Two knobs are provided so that the top and bottom heating element temperatures can be adjusted independently. Turning one of the knobs to the “OFF” position allows one-sided toasting (for bagels, etc.)

•“LOW” is the lowest temperature setting, which produces a lighter toasting of the bakery product on its top or bottom.

•“HIGH” is the highest temperature setting, which produces a darker toasting of the bakery product on its top or bottom.

2