VCR2 and reprogram the remote control | Toshiba 36HF12 manual

Programming the remote control for use with a non-Toshiba VCR or cable TV converter

The remote control is pre-programmed to operate Toshiba VCRs. To use the remote control to operate a non-Toshiba VCR or cable converter, follow the steps below to program the remote control.

1.Refer to the “VCR code table” or “Cable TV converter code table” on pages 16-17 to find the corresponding code for your VCR or cable TV converter brand.

If more than one code is listed, try each one separately until you find the one that works.

2.If you are reprogramming the remote control to operate your:

•VCR: Set the TV/CABLE/VCR switch on the remote control to VCR.

•Cable converter: Set the TV/CABLE/VCR switch on the remote control to CABLE.

3.While holding down the RECALL button, press the Number buttons (0-9) to enter the three-digit code for your VCR or cable TV converter.

4.Point the remote control at the VCR or converter and press POWER to test the code.

If the VCR or converter responds, you have entered the correct code.

If the VCR or converter does not respond, you may have entered the wrong code. Repeat steps 1-4 using another code.

5.Reset the TV/CABLE/VCR switch to TV to control the TV.

For future reference, write down the code(s) you used:

VCR code ________________________________

Cable TV converter code ____________________

				RECALL
	LIGHT	RECALL POWER
TV				POWER
TV
CABLE	MUTE	TV/VIDEO TIMER
VCR	MUTE	TV/VIDEO TIMER
VCR
1	2	3		Channel yz
			CH	Channel yz
4	5	6		Channel
7	8	9		Channel
7	8	9		Number
		CH RTN	VOL	Number
		CH RTN	VOL
100	0	ENT		Enter
				Enter
	ADV/
FAVORITE	PIP CH		PIC
FAVORITE			PIC
			SIZE
FAV	MENU/		FAV
FAV	ENTER		FAV
	ENTER
STROBE	ADV/		EXIT
	PIP CH
STOP SOURCE		PLAY PIP
REC	TV/VCR	REW	FF

Note:

•Each timeSTILLyouLOCATEreplaceSWAP the batteries, you must reprogram the remote control.

•Some newer VCRs are capable of working on either of two remote codes. These VCRs have a switch labeled “VCR1/VCR2.”

If your VCR has this kind of switch, it may not respond to any of the code numbers for your VCR brand name. In this case, set the switch to the other position (VCR1 or

VCR2) and reprogram the remote control.

Introduction


Connecting	yourTV


Usingthe	RemoteControl


Settingup	yourTV


UsingtheTV’s	Features


Appendix


Index

15

Image 15

Toshiba 36HF12 owner manual VCR2 and reprogram the remote control

Contents

36HF12 Dear Customer Safety Precautions Installation Important Safety Instructions Care Service Introduction Exploring your new TV IntroductionPlease Note Welcome to Toshiba Connecting a VCR Connecting your TV From Cable Connecting a cable converter boxConnecting a cable converter box and VCR Connecting your TV Settingup YourTV UsingtheTV’s Features Appendix Index Connecting a DVD player or satellite receiver and a VCRIntroduction Connecting YourTV Control Using DVD player with component video DTV receiver with component video Introduction Connecting YourTV Usingthe RemoteControlFrom Antenna Camcorder Connecting two VCRsConnecting a camcorder From Antenna To A/V Receiver Connecting an audio systemConnecting an A/V receiver Settingup YourTV Using the remote control with a VCR or cable TV converter Using the remote controlPreparing the remote control for use Installing the remote control batteries VCR2 and reprogram the remote control Brand name Code number VCR code table ABC Cable TV converter code table Exit exits programming menus Learning about the remote control UsingtheTV’s Features Setting up your TVIntroduction Connecting YourTV Usingthe RemoteControl Settingup YourTV Press x or to highlight your desired language Setting up your TVChanging the on-screen display language Selecting the antenna input Press z to select CH Program Adding channels to the TV’s memoryProgramming channels automatically Adding and erasing channels manually Press y or z to highlight ADD/ERASE Adjusting the tilt correction featureChanging channels using SpeedSurf Changing channels Programming your favorite channels Using the TV’s featuresAdjusting the channel settings Switching between two channels Labeling channels Using the TV’s Features MENU/ENTER Picture tube than in the Compression mode Viewing the wide-screen picture formatsSelecting the image shape Watching PIP/double-window Setting YourTV UsingtheTV’s Features AppendixPIP mode Example PIP mode Changing the position of the small picture Switching the main and sub-picturesPIP mode Double-window mode Example PIP mode Still Setting Your UsingtheTV’s Features Using the multi-window featureUsing the favorite function Using the strobe function Continue to set each item following the steps on the next Using the Locks menuPress y or z to display the PIN code entering mode Entering the PIN code Using the V-CHIP menu Usingthe RemoteTV Rating Independent rating system for broadcasters Press x or to return to the Locks menu Mpaa Rating Independent rating system for movies Locking channels Unlocking programs temporarilyRepeat steps 3 and 4 for other channels Press y or z to highlight Clear ALL, and then press x or Locking video inputs Buttons to be locked Using the front panel lock featureChanging the PIN code Press Enter New PIN code is now active Adjusting the picture Selecting the picture modeAdjusting the picture quality Saving new preference Using the flesh tone featureUsing the Digital Noise Reduction DNR feature To turn off the DNR feature Highlight OFF in above Selecting the cinema mode Selecting the color temperatureResetting picture adjustments Connecting YourTV Control Selecting the video input sourceLabeling the video input sources To view text, highlight T1, T2, T3, or T4 Using the closed caption feature Setting the sleep timer Setting the clockTo set the clock Adjusting the sound Muting the soundSelecting stereo/SAP broadcasts Adjusting the sound quality Using the SRS 3D surround sound feature Resetting audio adjustments Using the sub-bass system SBSTo turn off the SBS Highlight OFF in above Turning off the built-in speakers Selecting the Audio OUT soundTo turn on the built-in speakers Highlight on in above Using the StableSound feature Selecting the background of the menu displayDisplaying on-screen information Viewing the demonstration mode Understanding the auto power off featureUnderstanding the last mode memory feature Appendix Specifications T2, T3, or T4. Turn closed captioning OFF TroubleshootingAntenna Black box appears on the screen Limited United States Warranty Limited Canada Warranty Channel programming IndexPage Manufactured by