
Adding channels to the TV’s memory
When you press Channel y or z, your TV will stop only on the channels stored in the TV’s channel memory.
Follow the steps below and on the next page to program all active channels into the TV’s memory.
Programming channels automatically
Your TV can automatically detect all active channels in your area and store them in its memory. After the channels are stored automatically, you can manually add or erase individual channels.
To program channels automatically:
1.Press MENU, and then press x or • until the SET UP menu appears.
2.Press y or z until the TV/CABLE is highlighted.
3.Press x or • to highlight either TV or CABLE, depending on which you use. If you use an antenna, highlight TV; if you use cable, highlight CABLE.
|
| SET UP |
|
|
|
LANGUAGE | ENGL I SH | ||||
CLOCK SET | 0 0 : 0 0 |
| |||
ANT 1 / 2 | ANT1 | ||||
TV / CABLE | TV / | CABLE |
| ||
CH PROGRAM |
|
|
| ||
ADD / ERASE | ADD | ||||
T I LT CORRECT I ON | 0 |
|
|
4. Press z to select CH PROGRAM.
|
| SET UP |
|
LANGUAGE | ENGL I SH | ||
CLOCK SET | 0 0 : 0 0 | ||
ANT 1 / 2 | ANT1 | ||
TV / CABLE | CABLE | ||
CH PROGRAM |
| ||
ADD / ERASE | ADD | ||
T I LT CORRECT I ON | 0 |
5.Press x or • to start channel programming. The TV will automatically cycle through all the TV or Cable channels (depending on which you selected), and store all active channels in the channel memory.
While the TV is cycling through the channels, the message “Programming
6.When channel programming is complete,the message “Completed” appears.
7.Press Channel y or z to view the programmed channels.
Adding and erasing channels manually
After you have programmed the channels automatically, you can manually add or erase specific channels.
To add or erase channels:
1.Select the channel you want to add or erase. If you are adding a channel, you must select the channel using the Channel Number buttons.
2.Press MENU, and then press x or • until the SET UP menu appears.
(continued on next page)
Note:
To tune the TV to a channel not programmed in the channel memory, you must use the Channel Number buttons on the remote control.
| LIGHT | RECALL POWER | |
TV |
|
| |
CABLE | MUTE | TV/VIDEO TIMER | |
VCR | |||
|
|
1 | 2 | 3 |
| Channel yz |
|
|
| CH | |
4 | 5 | 6 |
|
|
7 | 8 | 9 |
|
|
|
| CH RTN | VOL |
|
100 | 0 | ENT |
|
|
| ADV/ |
|
| |
FAVORITE | PIP CH | PIC |
| |
|
|
| SIZE |
|
| MENU/ |
| MENU | |
FAV | FAV |
| ||
ENTER |
| |||
|
| yzx • | ||
|
|
|
| |
STPOBE | ADV/ | EXIT |
| |
| PIP CH |
|
| |
STOP SOURCE | PLAY PIP |
| ||
REC | TV/VCR | REW | FF |
|
| STILL | LOCATE SWAP |
|
Introduction |
|
|
|
|
|
Connecting | yourTV |
|
|
|
|
Usingthe | RemoteControl |
|
|
|
|
Settingup | yourTV |
|
|
|
|
UsingtheTV’s | Features |
|
|
|
|
Appendix |
|
|
|
|
|
Index |
|
|
|
21