Getting started
Manual Search - digital only -
If there were any missing channel after Full Search, these channels might be found by using Manual Search described in this section.
1From the Setup menu, press or to select Manual Search.
2Press 
, then press or to select the channel(0~69) you wish to search.
DTV Menu...[Setup...Manual Search] |
| |
Language |
|
|
Country/Region |
|
|
Full Search | Channel Number | 21 |
Quick Search | Signal Strength | 0% |
Auto Tuning - analog only -
First, use the Auto Tuning function to preset all the active channels in your area automatically. Then, arrange the preset channels with the Manual Adjust function so that you can tune into desired channels.
1Press 
, and or to select the Setup menu.
2Press 
and or to select Auto Tuning menu.
3Press 
, a confirmation screen will appear indicating that This will do auto tuning , Are you sure?
ATV Menu...[Setup...Auto Tuning]
Language
Country/Region | Auto Tuning Confirm |
Manual Search |
|
Channel List |
|
Fav Group : 1 |
|
OK Confirm MENU Return | Navigate EXIT Cancel |
Auto Tuning
Manual Adjust
Channel List
Fav Group : 1
Fav Group : 2
This will do auto tuning, Are you sure?
3If scanning was successful, Signal Strength will appear at almost 100%. Repeat to scan other channels as necessary.
|
|
|
|
|
|
|
|
|
| DTV Menu...[Setup...Manual Search] |
|
|
|
|
| ||
| Language |
|
|
|
|
|
|
|
| Country/Region |
|
|
|
|
|
| |
| Full Search |
| Channel Number | 21 |
|
|
| |
| Quick Search |
| Signal Strength |
|
| 100% |
| |
| Manual Search |
|
|
|
|
|
|
|
| Channel List |
|
|
|
|
|
|
|
| Fav Group : 1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| OK Confirm | MENU Return | Navigate | EXIT Cancel | ||||
4If scanning was unsuccessful, Signal Strength will appear at almost 0%.
At this point you can rescan the signal or refer to aligning the direction of the antenna to get the signal. Refer to your antenna installer if problem persists.
Notes:
•Signal Strength refers to the input Radio Frequency (RF) signal strength as perceived by the TV. Note that too strong signal may cause erroneous readings. If you use an antenna booster and find that you still get a low signal level, your booster gain may be set too high. In this case, adjust the gain accordingly. You may also see the No Signal on the screen when the signal level is low.
OK Confirm MENU Return | Navigate EXIT Cancel |
4Press 
to start the automatic search.
The search will begin for all available stations.
|
|
|
|
|
|
ATV Menu...[Setup...Auto Tuning] |
|
| |||
Language |
|
|
|
|
|
Country/Region |
|
|
| ATV Channels: 0 | |
Auto Tuning |
|
|
|
|
|
Manual Adjust |
|
|
|
|
|
Channel List |
|
|
|
|
|
Fav Group : 1 |
|
|
| VL | |
Fav Group : 2 |
|
|
| 10% |
|
|
|
|
|
| |
|
|
|
|
|
|
OK Confirm MENU Return | Navigate EXIT Cancel | ||||
The slide bar will move along line as the search progresses.
If you make a mistake, simply repeat steps
5When the automatic search is completed, the TV will automatically return to the first program position.
6Press 
or
to view the programmed position.
Note:
When you preset the program channel which sound of broadcast transmission system adopts “M” system, the sound system may not be tuned correctly if the radio waves transmit badly. At that time, preset the channel by Manual Search.
14
