Toshiba 40RF350U manual Connecting an Hdmi or DVI device to the Hdmi input

Chapter 2: Connecting your TV

Connecting an HDMI™ or DVI device to the HDMI input

The HDMI input on your TV receives digital audio and uncompressed digital video from an HDMI source device, or uncompressed digital video from a DVI (Digital Visual Interface) source device.

This input is designed to accept HDCP (High-Bandwidth Digital-Content Protection) program material in digital form from EIA/CEA-861-D–compliant[1]consumer electronic devices (such as a set-top box or DVD player with HDMI or DVI output).

The HDMI input can accept and display VGA, SVGA, XGA, WXGA, SXGA, 480i (60Hz), 480p (60Hz), 720p (60Hz), 1080i (60Hz), and 1080p (24Hz/60Hz) signal formats. For detailed signal specifications, see page 79.

Supported Audio format: Linear PCM, sampling rate 32/44.1/ 48 kHz

Note:

•Some legacy HDMI sources may not work properly with your latest HDMI TV, due to the adoption of a new standard. Please unplug your HDMI cable(s) first and try setting the following two options (Lip-Sync Latency, xvYCC) to “Off”. Now your legacy HDMI source should operate properly with your TV. See page 68.

•To connect a PC to the HDMI input, see page 22.

To connect an HDMI device, you will need:

•one HDMI cable (type A connector) per HDMI device

–For proper operation, it is recommended that you use an

HDMI cable with the HDMI Logo ( ).

–If your HDMI connection is capable of 1080p and/or your TV is capable of refresh rates greater than 60Hz, you will need a Category 2 cable. Conventional HDMI/DVI cable may not work properly with this mode.

–HDMI cable transfers both video and audio. Separate analog audio cables are not required (see illustration).

–See “Setting the HDMI™ audio mode” (- page 43).

TV lower back panel

HDMI device

VIDEO	AUDIO	HDMI OUT
L	R

IN IN

OUT

LR

To view the HDMI device video:

Select the HDMI 1, HDMI 2, or HDMI 3 video input source on the TV.*

*To select the video input source, press INPUT on the remote control (- page 24). To program the TV remote control to operate other devices, see Chapter 3.

To connect a DVI device, you will need:

•one HDMI-to-DVI adapter cable (HDMI type A connector) per DVI device

–For proper operation, the length of an HDMI-to-DVI adapter cable should not exceed 9.8 ft (3m). The recommended length is 6.6 ft (2m).

•one pair of standard analog audio cables per DVI device

–An HDMI-to-DVI adapter cable transfers video only. Separate analog audio cables are required (see illustration).

–See “Setting the HDMI™ audio mode” (- page 43).

TV upper back panel TV lower back panel

DVI device

VIDEO	AUDIO	DVI/HDCP
L	R	OUT
	IN IN

	OUT
L	R

Note: To ensure that the HDMI or DVI device is reset properly, it is recommended that you follow these procedures:

•When turning on your electronic components, turn on the TV first, and then the HDMI or DVI device.

•When turning off your electronic components, turn off the HDMI or DVI device first, and then the TV.

[1]EIA/CEA-861-D compliance covers the transmission of uncompressed digital video with high-bandwidth digital content protection, which is being standardized for reception of high- definition video signals. Because this is an evolving technology, it is possible that some devices may not operate properly with the TV.

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

19