Select the first channel you want to view.

Chapter 6: Using the TV’s features

To set the Channel Tuning Mode:

1 Press Yand open the Setup menu.

2 Highlight Installation and press T.

3 (A new set of Installation menu icons will appear, as shown below.) Open the Terrestrial menu, highlight Channel Tuning Mode, and then press B b to select your desired mode.

Installation

Terrestrial

Input Configuration

 

 

 

 

 

 

 

Channel Program

 

 

 

 

 

 

 

Channel Add/Delete

 

 

 

Channel Tuning Mode

Standa

rd

Standard

Signal Meter

 

 

Auto

 

 

Digital

Note:

The Channel Add/Delete & Channels Block windows as well as the Channel Browser ANT list will be updated automatically when you change the mode. Also, the History List will be cleared, but the Favorites List will be saved.

Even if the Channel Tuning Mode is set to Digital, analog channel 3 will still be the default channel to prevent the initial case where no digital channels have been found in prior channel scans. (Channel Add/Delete will not have anything listed until a scan is done.)

Tuning to the next programmed channel

To tune to the next programmed channel:

Press <or ,on the remote control or TV control panel.

Note:This feature will not work unless you program channels into the TV’s channel memory (- page 40).

Tuning to a specific channel (programmed or unprogrammed)

Press the Channel Number (0–9) on the remote control. For example, to select channel 125 (or channel 125-1), press 1, 2, 5, then T. Your TV will tune to the analog or digital channel according to the Channel Tuning Mode setting:

If the Channel Tuning Mode is set to Standard, the TV will tune to analog channel 125. To tune to digital channels,

press the Channel Number (0–9) on the remote control, followed by the dash (=) button and then the sub-channel

number. For example, to select digital channel 125-1, press 1, 2, 5, -, 1, then T.

If the Channel Tuning Mode is set to Auto, the TV will tune to digital channel 125-1 if it exists, if not then analog channel 125.

If the Channel Tuning Mode is set to Digital, the TV will tune to digital channel 125-1. (It is not possible to tune analog channels by entering the Channel Number (0–9).)

Note: If a digital channel is not programmed—either through the automatic channel scan (- page 40) or the Channel Add/ Delete function (- page 40)—you will have to tune the RF channel using the Channel Number and dash (=) on the remote control.

Switching between two channels using Channel Return

The Channel Return feature allows you to switch between two channels without entering an actual channel number each time.

1

2 Select a second channel using the Channel Number buttons (and the dash (=) button if selecting a digital channel).

3 Press Ron the remote control. The previous channel will display. Each time you press R, the TV will switch back and forth between the last two channels that were tuned.

Note:

If you press Rfrom a non-antenna input, the TV will return to the last-viewed input.

If the previous channel or memorized channel was an

analog channel and you change the Channel Tuning Mode to Digital, “NOT AVAILABLE” will be displayed if Ris pressed.

Switching between two channels using SurfLock

The SurfLockfeature temporarily “memorizes” one channel to the Rbutton, so you can return to that channel quickly from any other channel by pressing R. To memorize a channel to the Rbutton:

1 Tune the TV to the channel you want to program into the

Rbutton.

2 Press and hold Rfor about 2 seconds until the message “Channel Memorized” appears on-screen. The channel has been programmed to the Rbutton.

3 You can then change channels repeatedly, and when you press R, the memorized channel will be tuned.

The TV will return to the memorized channel one time only. Once you press Rand then change channels again, the CH RTN memory will be cleared and the button will function as Channel Return, by switching back and forth between the last two channels that are tuned.This feature also works for external inputs.

50

Page 50
Image 50
Toshiba 40RF350U Tuning to a specific channel programmed or unprogrammed, Switching between two channels using SurfLock