Chapter 6: Setting up your TV

Programming channels into the TV’s channel memory (continued)

Manually adding and deleting channels in the channel memory

After automatically programming channels into the channel memory, you can manually add or delete individual channels.

To add or delete channels in the channel memory:

1.Press MENU and open the Setup menu.

2.Highlight Installation and press ENTER. (A new set of Installation menu icons will appear on-screen, as shown in step 3).

Setup

 

Installation

 

 

 

 

 

 

 

 

 

Sleep Timer

 

 

 

 

 

 

 

 

 

On/Off Timer

 

 

 

 

 

 

 

 

 

HDMI 1 Audio

 

Auto

 

 

 

 

 

 

 

HDMI 2 Audio

 

Auto

 

 

 

 

 

 

 

Slide Show Interval

 

2 Sec

 

 

 

 

 

 

 

AVHD Skip Time

 

15 min

 

 

 

 

 

 

 

Navigate

Select CH RTN Back EXIT Exit

 

 

 

 

 

3.Open the Terrestrial menu, highlight Channel Add/Delete, and then press ENTER.

Terrestrial

Input Configuration

Channel Program

Channel Add/Delete

Signal Meter

Navigate

Select CH RTN Back EXIT Exit

 

 

4.The illustration below left shows channels programmed for the ANT 1 antenna input. To view the list of channels programmed for the Cable box or ANT 2 antenna input, press the y z buttons to highlight either “ANT 2” or “Cable Box” and press ENTER.

Note: “Cable Box” will appear only if you connected a cable box to your TV.

Channel Add/Delete

 

 

ANT 1

 

Channel Add/Delete

 

 

ANT 2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

 

Analog

 

ANT 1

 

 

 

 

1

Analog

 

ANT 1

 

 

 

 

 

 

 

2 - 1

Digital

ANT 2

2

Analog

ANT 2

2 - 2

Digital

Cable Box

3

Analog

Cable Box

 

 

3

Analog

 

 

 

 

 

4

Analog

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

Analog

 

 

 

 

 

5

Analog

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5

Analog

 

 

 

 

 

6

Analog

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6

Analog

 

 

 

 

 

7

Analog

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7

Analog

 

Reset

 

 

 

8

Analog

 

Reset

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7 - 1

Digital

 

Cancel

 

 

 

9

Analog

 

Cancel

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8

Analog

Done

10

Analog

Done

To add a channel to the channel memory:

Highlight the unchecked box next to the channel number you want to add, and then press ENTER to check the box.

To manually add digital subchannels on a physical channel:

Use the Channel Numbers and the Dash (–/100) on the remote control to enter the channel number (for example, 56–1).

If the channel is found, the number will be added to the list and the box will be checked.

If the channel is not found, a message will appear.

To remove a channel from the channel memory:

Highlight the checked box next to the channel number you want to remove, and then press ENTER to uncheck the box.

To save your new settings:

Highlight Done and press ENTER.

To revert to your original settings:

Highlight Cancel and press ENTER before saving.

To remove all channels from the channel memory:

Highlight Reset and press ENTER, and then highlight Done and press ENTER.

Note:

This action applies to the current antenna input only. To delete/add channels on the other input, highlight the input you want (ANT1 or ANT 2) and press ENTER.

This action cannot be cancelled unless you highlight Cancel and press ENTER before saving your changes.

Channel Add/Delete

 

 

ANT 1

 

 

 

 

 

 

 

 

 

 

 

2

 

Analog

 

ANT 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2 - 1

 

Digital

 

ANT 2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2 - 2

 

Digital

 

Cable Box

 

 

 

 

 

 

 

 

 

 

 

 

 

3

 

Analog

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

 

Analog

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5

 

Digital

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6

 

Analog

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7

 

Analog

 

Reset

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7 - 1

 

Digital

 

Cancel

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8

 

Analog

 

Done

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Copyright © 2005 TOSHIBA CORPORATION. All rights reserved.

43

 

Page 43
Image 43
Toshiba 46HM15, 62HM15A owner manual Manually adding and deleting channels in the channel memory